00196693-03_UM_SX4DX4_SR706_EN.pdf - 第329页
User Manual SIPLACE SX4/DX4 6 Station extensions From software version SC.706.xx Version 06/2012 EN 6.5 Docking station for the component trolley of the SIPLACE X series 329 CAUTION 6 When raising and loweri ng the compo…
6 Station extensions User Manual SIPLACE SX4/DX4
6.5 Docking station for the component trolley of the SIPLACE X series From software version SC.706.xx Version 06/2012 EN
328
6.5.5.1 Tools
You will need the following tools to adjust the height of the component trolley docking unit:
– Allen wrench, set
– Fork wrench, SW 13
6.5.5.2 Converting the component trolley docking unit to other heights
WARNING 6
Disconnect the docking station from the power supply.
Disconnect the docking station from the compressed air supply.
The weight of the component trolley docking unit is approx. 40 kg.
If required, enlist the help of a second person to help you with the conversion.
Follow the steps in the order described.
6.5.5.3 Converting the component trolley docking unit to heights of 900, 930 or 950 mm
6
Fig. 6.5 - 6 Order of conversion steps
Loosen the two hexagon socket-head screws M8x18 (item 9 in fig. 6.5 - 5, page 327) and re-
move the left and right guidance (item 8 in fig. 6.5 - 5
, page 327).
User Manual SIPLACE SX4/DX4 6 Station extensions
From software version SC.706.xx Version 06/2012 EN 6.5 Docking station for the component trolley of the SIPLACE X series
329
CAUTION 6
When raising and lowering the component trolley docking unit, make sure that no cables are
damaged.
Unscrew the two screwed connections (item 3 in fig. 6.5 - 5, page 327).
Loosen the two other screwed connections (item 2 in fig. 6.5 - 5, page 327).
Remove the two M8 hexagonal nuts and washers (item 4 in fig. 6.5 - 5, page 327).
Hold the component trolley docking unit by its side (item 10 in fig. 6.5 - 5, page 327) and re-
move the two hexagon socket-head screws M8x40 here.
Swivel the component trolley docking unit to the next highest position.
Fasten the side panel at this point. Tighten the nuts loosely to do this.
Hold the component trolley docking unit by the FCU (item 12 in fig. 6.5 - 5, page 327) and
remove the screwed connections at item 2 in fig. 6.5 - 5
, page 327.
Swivel the component trolley docking unit to the next highest position.
Fasten the side panel at this point.
Check that all screwed connections at items 2, 3 and 4 are tightened firmly.
Fasten the right and left guidances (item 8 in fig. 6.5 - 5, page 327) with the hexagon socket-
head screw M8x18 (item 9 in fig. 6.5 - 5
, page 327).
PLEASE NOTE 6
If you want to lower the component trolley docking unit to a different height, follow the above
instructions in reverse order.
6 Station extensions User Manual SIPLACE SX4/DX4
6.6 Sensor for the component reject bin From software version SC.706.xx Version 06/2012 EN
330
6.6 Sensor for the component reject bin
Item no. 00519848-xx query for component reject bin
The sensor for the component reject bin monitors whether the reject bin is seated correctly in its
mount.
– If the reject bin was not inserted correctly, the machine cannot be started.
– If the reject bin jumps out of its mount during the placement process, the machine is stopped
immediately to avoid a head crash.
Each reject bin can be monitored by a separate sensor.
PLEASE NOTE 6
When using a SpeedStar we recommend that you install the optional sensor for the component
reject bin.