00196693-03_UM_SX4DX4_SR706_EN.pdf - 第266页
5 Working with the machine User Manual SIPLACE SX4/DX4 5.9 Carrying out a sight check From softw are version SC.706.xx Version 0 6/2012 EN 266 5.9.3 Checking the PCB support s Check the position of the magnetic PCB sup…
User Manual SIPLACE SX4/DX4 5 Working with the machine
From software version SC.706.xx Version 06/2012 EN 5.9 Carrying out a sight check
265
Check to see whether the tape foil removal container for the X tape feeder module is full.
Open the flap (item 1). Pull out the cover foil and cut it with scissors or on the integral blade
(item 2) on 8 and 12 mm X tape feeder modules.
PLEASE NOTE 5
Never tear the cover foil. This can cause problems with the cover foil pull-off. There is an in-
tegral blade (item 2) for easily cutting the on the 8 and 12 mm X tape feeder modules.
Check the multicolor status display (item 3 in fig. 5.9 - 1, page 264).
– If it lights up green, the feeder module is on standby.
– If it lights up orange, it is signaling a warning. The text of the warning
appears on the LCD display (item 4 in fig. 5.9 - 1
, page 264). The LEDs shine accordingly
for Smart Feeders.
– If the status display lights up red, a malfunction has occurred. The error message
appears on the LCD display (item 3 in fig. 5.9 - 1
, page 264). The LEDs shine accordingly
for Smart Feeders.
A list of the LCD and status displays on the operator panel is given in section 5.11
, page
280
. 5
A list of the LED and status displays on the Smart Feeder operator panel is given in sec-
tion 5.11.2
, page 281. 5
If the status display is off, the cause may be as follows: 5
– The feeder module is not in the current setup.
– The feeder module is defective.
– The feeder module has been disabled (due to a drop in pressure, for example)
5.9.2 Splicing the tapes in good time
PLEASE NOTE:
Splice the tapes early enough so that the feeder modules do not run out of components. Oth-
erwise you will experience prolonged down times.
However, do not splice the tapes too early because if you wind the end of the old tape onto
the new reel after splicing, the reel holding the new tape may become overfilled and the tape
will slip off the reel and become tangled up. This will again result in pick-up errors and pro-
longed down times. 5
5 Working with the machine User Manual SIPLACE SX4/DX4
5.9 Carrying out a sight check From software version SC.706.xx Version 06/2012 EN
266
5.9.3 Checking the PCB supports
Check the position of the magnetic PCB supports on the lifting table:
– Make sure that the PCB supports do not collide with components on the underside of the
PCBs.
– In addition, make sure that the PCB supports do not collide with the PCB conveyor pan-
els.
– Only use PCB supports as described in section 6.12
, page 337.
User Manual SIPLACE SX4/DX4 5 Working with the machine
From software version SC.706.xx Version 06/2012 EN 5.9 Carrying out a sight check
267
5.9.4 Support for an additional tape reel
5
Fig. 5.9 - 2 Support for the additional tape reel
(1) Support for an additional tape reel, item no. 00141217-xx
(2) Mounting device for the support
5
X series feeder modules can process component tapes without problems if the lateral offset be-
tween the feeder module and the tape reel does not exceed 60 mm.
If a predefined setup means that the maximum permitted offset cannot be maintained, we recom-
mend that you use the mount for an additional tape reel (item 1). Simply insert the mount into the
holder (item 2) and push it until the offset is less than the maximum permitted value of 60 mm. The
component trolley has 5 holders in total. Each tape reel mount can hold 2 tape reels, which means
that up to ten 15" (381 mm) reels can be positioned above the tape container.
max. 60 mm