JUKI贴片机错误代码集合.pdf - 第103页
E500602 “ An error occurred while performin g Yc table end check. Code : % d ” “ 结束 Yc 支撑台检查时， 发生错误。 | 代码 : % d ” E500603 “ An error occurred while perform i ng axis end check. Code : %d ” “ 结束轴移动检查时，发生错误。 | 代码 : % d ” E…
again.”
“机器发生异常，请退出生产，关闭系统后，重新启动。”
E500500 “Teaching can not be executed”
“不能执行示教。”
[Cause]
You are trying to teach unexecuted data to the machine.
Unexecuted data:
Data except ref. circuit in the Placement position teaching.
Components except tray component in the Pick position teaching.
When multiple heads are working at the same time.
[Treatment]
You can not perform a teaching with the current status. Please go on the process.
E500501 “The selected device can not be used”
“不能使用被选设备。”
[Cause]
You selected a device not available.
[Treatment]
Please change devices to use.
E500502 “With the selected device, it is impossible to move to the aimed position”
“被选设备不能移到目的位置。”
[Cause]
You can not move to the specified position with the selected device.
[Treatment]
Please select another device.
E500503 “Standard Pin position illegal. Correct coordinates can not acquire”
“基准针位置不对。|不能取得正确坐标。”
[Cause]
The position of the reference pin is not correct.
[Treatment]
In the Setup, please teach the positions of the reference pin and follower pin to the machine.
E500600 “YC table error. Code : %d”
“Yc 支撑台出错。|代码 : %d”
E500601 “Axis movement error. Code : %d”
“轴通讯错误”
E500602 “An error occurred while performing Yc table end check. Code : %d”
“结束 Yc 支撑台检查时，发生错误。|代码 : %d”
E500603 “An error occurred while performing axis end check. Code : %d”
“结束轴移动检查时，发生错误。|代码 : %d”
E500605 “An error occurred when disposing a component”
“废弃组件发生错误。”
[Cause]
This error occurs if the component present check at a component disposal action gets an error when
starting a production.
[Treatment]
Pressing OK button will abort the process. In this case, the production will not be executed.
E500700 “An error occurred while Auto. PWB Width Alignment Control. | The process gets discontinued”
“自动调整基板宽度发生错误。|退出操作。”
[Cause]
This error occurs if an error occurs or an action did not take place properly while Auto. PWB Width
Alignment Control.
[Treatment]
Pressing OK button will abort the process. If a particular reason (Home returning has not been
complete, etc.) why Auto. PWB Width Alignment Control can not be executed is given, please
perform any means to get rid of the factor that stops Auto. PWB Width Alignment Control. If any
particular reasons are not given, please, check the action of Auto. PWB Width Alignment Control by
Manual control .
E500701 “Para error. PWB Width Alignment Control occurred”
“自动调整基板宽度参数错误”
[Cause]
This error occurred if an entered value to be defined by Enter key is wrong when performing Auto.
PWB Width Alignment Control.
[Treatment]
Please check the entered value.
E500710 “An error occurred while Auto. BOC mark.|The process gets discontinued.”
“识别 BOC 标记发生错误|退出操作。”
E500711 “Param error|BOC mark occurred.”
“识别 BOC 标记参数错误”
E500800 “A PWB is detected within the conveyors of both stations. Please remove the PWB”
“两个站台内的传送轨道上，发现基板。|请取下基板。”
[Cause]
The production can not get started because PWBs are on the conveyors on both sides when starting
the production.
[Treatment]
Please remove the PWBs from the conveyors by pressing OK button, and then press START key
again.
E500801 “A PWB is detected within the conveyor of the Left station. Please remove the PWB”
“左边站台的传送轨道上，发现基板。|请取下基板。”
[Cause]
The production can not get started because a PWB is on the conveyor on left side when starting the
production.
[Treatment]
Please remove the PWBs from the conveyors by pressing OK button, and then press START key
again.
E500802 “A PWB is detected within the conveyor of the Right station. Please remove the PWB”
“右边站台的传送轨道上，发现基板。|请取下基板。”
[Cause]
The production can not get started because a PWB is on the conveyor on right side when starting the
production.
[Treatment]
Please remove the PWBs from the conveyors by pressing OK button, and then press START key
again.
E500803 “A PWB is detected within the conveyor.|Please remove the PWB.”
“在传送轨道上发现基板。|请取下基板。”
E500900 “The connection with HLC is on-line. The production is not available with the currently selected
production program created by the machine”
“HLC 处于联机状态。|不能以当前被选用的主机程序进行生产。”
[Cause]
The connection between your machine and HLC is set to ON in the Setup. The currently selected
production program was created by the machine. Therefore, its production can not get started.
[Treatment]
Please cut off the connection between your machine and HLC in the Setup or read in another
production program.
E500901 “It is not connected to HLC. The production is not available with the currently selected production
program created by HLC”
“没有连接 HLC。|不能以现在被选用的 HLC 程序进行生产。”