JUKI贴片机错误代码集合.pdf - 第114页
[Treatment] A detailed error message should ha ve been shown prior to thi s m essage. Please check and see the status, using the given error n umber. E502999 “ Abnormal stop. (%ld) ” “ 异常结束生产。 (%ld) ” E503001 “ Retry Lis…
E501852 “The type of the holder is different.(Type2)”
“ 固定器类型不同（Type2）。”
E501853 “The type of DTS is different.(Lane1)”
“ DTS 类型不同（Lane1）。 “
E501854 “The type of DTS is different.(Lane2)”
“ DTS 类型不同（Lane2）。 “
E501855 “The part name is different.”
“ 组件名不同。”
E501856 “The installation hole position becomes.”
“ 安装空位置不同。 “
E501857 “It is a multi tray.”
“ 多型托盘状态。”
E501858 “The type of feeder is different.”
“ 送料器类型不同。 “
E501880 “The nozzle cannot be returned. continue anyway?”
“ 放回吸嘴时失败， 是否继续处理？ “
E501999 “Abnormal stop <%s>“
“异常结束生产。<%s>“
[Cause]
This error occurs when an action does not end normally.
an action that was taking place when a production ended abnormally.
While transporting PWBs
While recognizing VCS
While recognizing IC marks
While recognizing BOC marks
While detecting bad marks
Placement position
Pick position
While recognizing L3
While installing a nozzle on a head
While returning a nozzle to ATC
While disposing a component
While reading bank marks
Other positions
[Treatment]
A detailed error message should have been shown prior to this message.
Please check and see the status, using the given error number.
E502999 “Abnormal stop. (%ld)”
“异常结束生产。(%ld)”
E503001 “Retry List message file (RETRYLIST.MSG) cannot be opened”
“不能打开重试列表提示文件(RTRYLIST.MSG)。”
[Cause]
Failed to open the Retry List message file.
[Treatment]
Please re-install the system.
E503100 “You try to set remain less than level now, OK?”
“组件剩余数小于标准值，是否继续设置？”
[Cause]
The number of components remaining becomes less than the warning level of the number of
components left.
[Treatment]
Yes : Sets the entered number of components remaining.
No : Gets you back to the number of components remaining that is before you set.
E503200 “It is not Program made by setting non-stop. A normal operation is not occasionally done when
producing as it is. Production start forcibly?”
“生产程序不适用不间断生产|(不间断生产已被选用)，|或者弃用不间断生产，或者修改生
产程序。”
[Cause]
This message appears when the Non-stop functionality is enabled in the Operation Option but the
production program does not take Non-stop.
[Treatment]
Please disable the Non-stop functionality in the Operation Option, or check the Pick data in the
production program.
W503201 “It is not Program made by setting MTC non-stop.|(The MTC non-stop operation is selected.)|Make
the function of the MTC non-stop be unused by the operation option or try to program production.”
“ 生产程序不适用 MTC 不间断生产|(MTC 不间断生产已被选用)，| 或者弃用 MTC 不间断
生产，或者修改生产程序。”
W503202 “It is not Program made by setting DTS non-stop.|(The DTS non-stop operation is selected.)|Make
the function of the DTS non-stop be unused by the operation option or try to program production.”
“ 生产程序不适用 DTS 不间断生产|(DTS 不间断生产已被选用)，| 或者弃用 DTS 不间断
生产，或者修改生产程序。”
W503203 “It is not Program made by setting MTS non-stop.|(The MTS non-stop operation is selected.)|Make
the function of the MTS non-stop be unused by the operation option or try to program production.”
“ 生产程序不适用 MTS 不间断生产|(MTS 不间断生产已被选用)，| 或者弃用 MTS 不间断
生产，或者修改生产程序。”
E503300 “%s feeder bank is in lower position”
“%s 送料器台架在下降。”
[Cause]
This message appears if a feeder bank is descending down when starting a production.
where the feeder bank is descending to.
On the front side
On the rear side
On both sides.
[Treatment]
Please press OK button after the feeder bank has ascended.
E503301 “MTC is in motion. Please wait for stop”
“MTC 正在运转中，|等待停止。”
[Cause]
This message appears if MTS is in operation when starting a production.
[Treatment]
Please press OK button after MTC's motion has been done. Pressing Cancel button will have you
back to the status that is before pressing START key.
E503302 “Cover open”机盖被打开”
[Cause]
This message appears at the beginning of a production if the production can not be produced with the
cover open.
[Treatment]
Please close the cover and press the START key again.
W503310 “An environment setting is checked. A normal production operation cannot be done.|Is production
started?”
“环境设置被选用，不能进行正常生产，|是否开始生产？”
E503400 “The sequence(%s) you selected is different from the one(%s) of when the production got suspended
illegally last time. Would you like to resume the production?”
“前一次结束生产时的顺序(%s)和这一次选择的顺序(%s)不一样，|是否开始继续生产？”