JUKI贴片机错误代码集合.pdf - 第387页
E694019 “ The mot or revolution is abnormal .” “ 马达旋 转次数异常。 ” E694020 “ A memory of s encer is abnormal .” “ 传感器 内存异常。 ” E694021 “ A i nitialize error of coplanarity unit .” “ 初始化 共面单元时发生错误。 ” E694022 “ An axis error of …
E694001 “A coplanarity judgemennt error.”
“ 共面检测错误。”
E694002 “A coplanarity centering position error.”
“ 共面检测时的端子位置偏移错误。”
E694003 “A lead count error.”
“ 引脚数错误。”
E694004 “A colinearity judgemennt error.”
“ 平行性判断错误。”
E694005 “A coplanarity measurement error.”
“ 共面检测时测量错误。”
E694006 “The measurement plane is too low.”
“ 共面测量高度过低。”
E694007 “The measurement plane is too high.”
“ 共面测量高度过高。”
E694011 “A coplanarity unit error.”
“ 共面测量单元错误。”
E694012 “A illegal data or illegal operation.”
“ 违规数据或违规操作引起的错误。”
E694013 “A coplanarity adjust error.”
“ 共面校准错误。”
E694014 “A time-out or other error.”
“ 超时或其它错误。”
E694015 “A hardware error of coplanarity controler.”
“ 控制共面的硬件出错。”
E694016 “A measurement software error.”
“ 测量软件有问题。”
E694017 “A lasor diode is abnormal.”
“ 激光超时错误。”
E694018 “A cable connection error.”
“ 传感器电缆连接异常。”
E694019 “The motor revolution is abnormal.”
“ 马达旋转次数异常。”
E694020 “A memory of sencer is abnormal.”
“ 传感器内存异常。”
E694021 “A initialize error of coplanarity unit.”
“ 初始化共面单元时发生错误。”
E694022 “An axis error of coplanarity measurement.”
“ 共面测量时轴发生错误。”
E694030 “The component type can not be measured.”
“ 指定的组件类型错误。”
E694031 “The component size is too large.”
“ 组件尺寸过大，超过测量范围。”
E694032 “The component size is out of range.”
“ 组件尺寸超过测量范围。”
E694033 “The component height is too high.”
“ 组件高度过高，超过测量范围。”
E694034 “The measurement mode is not correct or the component can not be measured.”
“ 指定的测量方法有问题或指定组件类型错误。”
E694035 “The electrode can not be measured.”
“ 所指定的电极不能测量。”
E694036 “A coplanarity sensor is unused.”
未用共面检测
E695012 “Parameter for the head is not correct.”
“HEAD参数不正确。”
E695013 “The bus error occurred by the laser board(L).|Please check a laser board.”
“激光板(L)总线发生错误。|请检查一下激光板。”
E695014 “The bus error occurred by the laser board(R).|Please check a laser board.”
“激光板(R)总线发生错误。|请检查一下激光板。”
E695015 “The bus error occurred by the laser board(L).”
“激光板(L)总线发生错误。”
E695016 “The bus error occurred by the laser board(R).”
“激光板(R)总线发生错误。”
E695017 “It failed in initialization of a laser board(L).”
“激光板(L)的初始化失败。”
E695018 “It failed in initialization of a laser board(R).”
“激光板(R)的初始化失败。”
E695019 “Timed out waiting for dsout to change. (EEPROM erase)”
E695020 “Timed out waiting for dsout to change. (EEPROM write)”
E695021 “The bus error occurred by the laser board.|Please check a laser board.”
“激光板总线发生错误。|请检查一下激光板。”
E696001 “The error occurred in reading of a PCI configuration register.”
“读PCI总线配置寄存器时发生错误。”
E696002 “The error occurred in the writing of a PCI configuration register.”
“写PCI总线配置寄存器时发生错误。”
E696003 “The error occurred in the address translation of a VME bus.”
“修改VME总线地址时发生错误。”
E696004 “The error occurred in memory allotment of a VME bus.”
“分配VME总线内存时发生错误。”
E696005 “The error occurred in memory release of a VME bus.”
“释放VME总线内存时发生错误。”
E696006 “The error occurred in the event creation for the notice of interruption.”
“建立中断通知用事件时发生错误。”
E696007 “The error occurred in registration of an interruption handler.”
“注册中断入口时发生错误。”
E696008 “The error occurred in release of an interruption handler.”
“释放中断入口时发生错误。”
E696009 “The parameter of a VME bus address is not right.”
“VME总线地址参数错误。”
E696010 “Abnormalities occurred to the VME power supply.”
“VME电源异常。”