JUKI贴片机错误代码集合.pdf - 第42页
“ TF 驱动错误 | 代码 : %ld ” E242547 “ MTS is not power on .” “ 没有打 开 MTS 电源。 ” E242548 “ MTS is not online .” “ 没有连 接 MTS 。 ” E242549 “ MTS is disable .” “ 不能使 用 MTS 。 ” E242600 “ MTS failed to pull a tray .” “ MTS 取出 托盘失败。 ”…
“组件过于倾斜。”
E242532 “Component size is too big.”
“组件外形尺寸过于偏大。”
E242533 “Component size is too small.”
“组件外形尺寸过于偏小。”
E242534 “Cannot recognize component.”
“不能识别组件。”
E242535 “Lead pitch of %s side is not conform.”
“%s 的引脚间距不一致。”
E242536 “Cannot recognize lead of %s side.”
“不能识别%s 的引脚间距。”
E242537 “Error has occurred during VCS measurement.|Code: %ld”
“VCS 测量组件发生错误。|代码: %ld”
E242538 “MTC is not power on.”
“没有打开 MTC 电源。”
E242539 “MTC is not online.”
“没有连接 MTC。”
E242540 “MTC is in the supply state.”
“MTC 处于补充状态。”
E242541 “MTC is disable.”
“不能使用 MTC。”
E242542 “MTC Emergency Switch is Pressed.”
“MTC 处于紧急停止状态。”
E242543 “MTC initialize not done.”
“未初始化 MTC。”
E242544 “MTC failed to a supply of a component.”
“MTC 供给组件失败。”
E242545 “The component remainder number is 0.”
“组件剩余数为 0。”
E242546 “TF driver error. |Code: %ld”
“TF 驱动错误 |代码: %ld”
E242547 “MTS is not power on.”
“没有打开 MTS 电源。”
E242548 “MTS is not online.”
“没有连接 MTS。”
E242549 “MTS is disable.”
“不能使用 MTS。”
E242600 “MTS failed to pull a tray.”
“MTS 取出托盘失败。”
E242601 “MTS failed to store a tray.”
“MTS 储存托盘失败。”
E242602 “MTS cannot move because of cover opening.”
“打开主机盖时，MTS 停止动作。”
E242603 “The door of MTS opens.”
“MTS 的门被打开。”
E242604 “The stacker of MTS is empty.”
“MTS 没有安装托盘存储箱。”
E242605 “MTS Emergency Switch is Pressed.”
“MTS 处于紧急停止状态。”
E242606 “MTS initialize not done.”
“未初始化 MTS。”
E242607 “DTS is disable.”
“不能使用 DTS。”
E242608 “DTS cannot be executed.”
“DTS 不能运行。”
E242609 “DTS is not initialized.”
“未初始化 DTS。”
E242610 “DTS safety cover opens.”
“DTS 安全盖被打开。”
E242611 “DTS is in the state of supply.”
“DTS 处于补充状态。”
E242612 “DTS failed in drawing out the tray.”
DTS取出托盘失败。”
E242613 “It failed in creating lighting data.”
“建立 VCS 照明数据失败。”
E242614 “The optimum value of lighting data was unacquirable.”
“不能取得照明数据优化值。”
E242615 “Component cannot be picked up.”
“不能吸取组件。”
E242616 “The state of DTS cannot be acquired.”
“不能取得 DTS 的状态。”
E242617 “The vision cannot be recognized. “
“不能进行图像识别。”
E242618 “Vision recognition condition data transmission error.”
“传送图像识别条件数据发生错误。”
E242619 “The head wait position is set in coordinates outside the moving range with a specified head.|Please
confirm the head wait position.”
“保护组件位置被设置在指定 Head 移动范围外的坐标。|请确认一下保护组件位置。”
E242620 “The pick position is set in coordinates outside the moving range with a specified head.”
“吸取位置被设置在指定 Head 移动范围外的坐标。”
E242621 “The SOT inspection stage is unused by the setup. “
“在设置中，SOT 检查器没有被选用。”
E242622 “The SOT inspection stage is dirty. Please remove the dirt of the SOT inspection stage.”
“SOT 检查器被弄脏。请清理 SOT 检查器。
E242623 “The lead does not exist within the detection window.”
“不能检测检查范围内的引脚。”
E242624 “Because directions of components of SOT are different by 180 degrees, the SOT direction cannot
be inspected.”
“因为 SOT 组件方向相差 180 度，不能检查 SOT 方向。”
E242625 “Because directions of components of SOT are different,the SOT direction cannot be inspected.”
“因为 SOT 组件方向不同，不能检查 SOT 方向。