JUKI贴片机错误代码集合.pdf - 第39页
E242503 “ Axis movement error (YC axis limit error) ” “ 轴移动发生错误 (YC 轴界限错误 ) ” E242504 “ Axis movement error (Z axis limit error) ” “ 轴移动发生错误 (Z 轴界限错误 ) ” E242505 “ Axis movement error (T axis limit error) ” “ 轴移动发生错误 (T …
“不存在 SOT 方向检查器。”
E241701 “The SOT direction inspection stage is an unuse unit.”
“SOT 方向检查器没有被选用。”
E241702 “The inspection error occurred.”
“检查发生错误。”
E241703 “The component size is out of range.”
“组件大小超出检查范围。”
Q241800 “%s|The optimum value of lighting data was acquirable.|(The basis in a prenthesis)|Is lighting data
updated?”
“%s|得到照明数据的优化值(括号内的是过去值)。| 是否更新照明数据? “
E241801 “The optimum value of lighting data was unacquirable.”
“不能取得照明数据的优化值。”
Q241802 “%sThe optimum value of light was acquirable.|(The basis in a prenthesis)|There is the influence of
inspection.Is lighting data updated?” 取得照明数据的优化值(括号内的是过去值)。|BGA 组
件的时候, 有时对检查精度有影响。|是否更新照明数据? “
E241900 “Coplanarity inspection is not specified.”
“没有指定共面检测器。”
E241901 “Coplanarity data was unacquirable. |Please confirm the height of component and lead width.”
“不能取得共面参数。|请确认一下组件高度和电极宽度。”
Q241902 “E.Brighthess Threshold %s (%s)|Scanning Offset %s (%s)|The optimum value of coplanarity
parameters was acquirable.|Is coplanarity parameters updated?”
“电极亮度阈值 %s (%s)|扫描位置的偏差 %s (%s)| 得到共面参数的优化值，是否更新参
数？”
E241903 “Centering of the component is no vision or lsc.”
“不属于外形定中心或 LSC 定中心的组件。 “
E242500 “The origin point return does not end.|Please retry after completing the origin point return.”
“未结束返回原点。|返回原点结束后，请再次运行。”
E242501 “The servo motor is free.|Please retry after releasing the servo free state.”
“伺服马达处于未起动状态。|请起动伺服马达后，再次运行。”
E242502 “Axis movement error (XY axis limit error)”
“轴移动发生错误(XY 轴界限错误)”
E242503 “Axis movement error (YC axis limit error)”
“轴移动发生错误(YC 轴界限错误)”
E242504 “Axis movement error (Z axis limit error)”
“轴移动发生错误(Z 轴界限错误)”
E242505 “Axis movement error (T axis limit error)”
“轴移动发生错误(T 轴界限错误)”
E242506 “Axis movement error (XY axis driver error)”
“轴移动发生错误(XY 轴驱动错误)”
E242507 “Axis movement error (YC axis driver error)”
“轴移动发生错误(YC 轴驱动错误)”
E242508 “Axis movement error (Z axis driver error)”
“轴移动发生错误(Z 轴驱动错误)”
E242509 “Axis movement error (T axis driver error)”
“轴移动发生错误(T 轴驱动错误)”
E242510 “The vacuum pressure cannot be measured.”
“取得真空压发生错误。(I/O 驱动错误)”
E242511 “No component.(Retry over of picking.)|Please confirm the existence of components.”
“无组件。(重试结束)|请确认一下组件是否存在。”
E242512 “Laser measurement error (ONCE measurement) | Code = %d (Please refer to the operation
manual.)”
“激光测量发生错误(ONCE 测量) | 代码 = %d (请查阅操作手册。)”
E242513 “Laser measurement error (Height measurement) | Code = %d (Please refer to the operation
manual.)”
“激光测量发生错误(高度测量) | 代码 = %d (请查阅操作手册。)”
E242514 “Laser measurement error (SWEEP measurement) | Code = %d (Please refer to the operation
manual.)”
“激光测量发生错误(SWEEP 测量) | 代码 = %d (请查阅操作手册。)”
E242515 “There is no %d nozzle. “
“%d 号吸嘴不存在。”
E242516 “The nozzle cannot be returned. “
“归还吸嘴失败。”
E242517 “The nozzle cannot be exchanged. “
“交换吸嘴失败。”
E242518 “The nozzle cannot be installed.”
“安装吸嘴失败。”
2
E242519 “There is no head which can be moved to the component pickup position.”
“Head 不能移到组件吸取坐标。”
E242520 “Component data error”
“组件数据错误。”
E242521 “The IC collection belt is unused by the setup. “
“在设置中，IC 回收器没有被选用。”
E242522 “The IC collection belt is fullness.”
“IC 回收器已被装满。”
E242523 “The chip standing was detected.”
“查出芯片站立。”
E242524 “The height of laser was not able to be measured from range.|Please confirm the height of
component.”
“不能检测在标准范围内的激光高度。|请确认一下组件高度。”
E242525 “The height of components was measured with 0mm or less.|Please confirm the height of laser.”
“测量组件高度结果为负值。|请确认一下组件高度。”
E242526 “Laser measurement error (MCM driver error) “
“激光测量发生错误(MCM 驱动错误) “
E242527 “Because the lower bound of being able the axis movement had been exceeded,|the height of the
laser was not able to be measured.”
“因为超过轴移动范围的下限，不能测量激光高度。”
E242528 “Could not change of mode for the chip verification system.”
“变更数值检查装置的测量模式失败。”
E242529 “Chip verification detection error.”
“数值检查装置测量发生错误。”
E242530 “The chip verification system is unused by the setup. “
“在设置中，数值检查装置没有被选用。”
E242531 “Component angle exceeds limit value.”