JUKI贴片机错误代码集合.pdf - 第44页
E242626 “ The error occurred by the SOT direction inspecti on by OCC.|Code :%ld ” “ OCC 检查 SOT 方向发生错误。 | 代码 :%ld ” E242627 “ The VCS device is set in unused by the setup. “ “ 在机器设置中，没有选用 VCS 。 ” E242628 “ The component s…
“DTS 处于补充状态。”
E242612 “DTS failed in drawing out the tray.”
DTS取出托盘失败。”
E242613 “It failed in creating lighting data.”
“建立 VCS 照明数据失败。”
E242614 “The optimum value of lighting data was unacquirable.”
“不能取得照明数据优化值。”
E242615 “Component cannot be picked up.”
“不能吸取组件。”
E242616 “The state of DTS cannot be acquired.”
“不能取得 DTS 的状态。”
E242617 “The vision cannot be recognized. “
“不能进行图像识别。”
E242618 “Vision recognition condition data transmission error.”
“传送图像识别条件数据发生错误。”
E242619 “The head wait position is set in coordinates outside the moving range with a specified head.|Please
confirm the head wait position.”
“保护组件位置被设置在指定 Head 移动范围外的坐标。|请确认一下保护组件位置。”
E242620 “The pick position is set in coordinates outside the moving range with a specified head.”
“吸取位置被设置在指定 Head 移动范围外的坐标。”
E242621 “The SOT inspection stage is unused by the setup. “
“在设置中，SOT 检查器没有被选用。”
E242622 “The SOT inspection stage is dirty. Please remove the dirt of the SOT inspection stage.”
“SOT 检查器被弄脏。请清理 SOT 检查器。
E242623 “The lead does not exist within the detection window.”
“不能检测检查范围内的引脚。”
E242624 “Because directions of components of SOT are different by 180 degrees, the SOT direction cannot
be inspected.”
“因为 SOT 组件方向相差 180 度，不能检查 SOT 方向。”
E242625 “Because directions of components of SOT are different,the SOT direction cannot be inspected.”
“因为 SOT 组件方向不同，不能检查 SOT 方向。
E242626 “The error occurred by the SOT direction inspection by OCC.|Code:%ld”
“OCC 检查 SOT 方向发生错误。|代码:%ld”
E242627 “The VCS device is set in unused by the setup. “
“在机器设置中，没有选用 VCS。”
E242628 “The component size is out of range.”
“组件大小超出检查范围。”
E242629 “The LSC device is set in unused by the setup. “
“在机器设置中，没有选用 LSC 。”
E242630 “It failed in creating lighting data.”
“建立 LSC 照明数据出错。 “
E242631 “The optimum value of lighting data was unacquirable.”
“取得照明数据的优化值失败。 “
E242632 “Axis movement error (XH axis limit error)”
“轴移动出错（XH 轴驱动出错）。”
E242633 “The lsc cannot be recognized. “
“未能识别 LSC。”
E242634 “Error has occurred during LSC measurement.|Code: %ld”
“用 LSC 测量组件时，发生出错。|代码：%ld “
E242635 “Cannot move the head to pick position.”
“不是能移到吸取组件坐标的 Head。”
I242550 “Please detach components from the nozzle by the hand. “
“请手动取下吸嘴上的组件。”
Q242551 “Return of thin components to tape may fail due to weight. | continue return?”
“因为组件太小(1mm),归还可能失败。|是否执行归还？”
I242552 “Please set online for MTC.”
“请连接 MTC。”
I242553 “Remove a component in the case that there is a component | on a shuttle of MTC.”
“如果 MTC 滑梭上存在组件，请把它取下。”
Q242554 “There is a possibility this component has not been picked correctly. |Do you want to
continue?|(Tombstone height = %s)”
“可能组件站立。|是否继续？|(检测组件站立高度 = %s)”
I242555 “Please set online for MTS.”
“请连接 MTS。”
I242556 “Please close the door of MTS.”
“请关闭 MTS 的门。”
I242557 “Please insert the stacker of MTS.”
“请装入 MTS 的托盘存储箱。”
I242558 “Please attach the component to the nozzle manually.”
“请手动给吸嘴安装组件。”
I242559 “The pickup of components succeeded. The measurement begins.”
“组件被成功吸着，开始测定。”
Q242560 “Failed in picking components. Do you want to make a retry?”
“组件吸着失败，是否重试？”
I242561 “Please install components by the hand in the chuck. When the button is pressed, the chuck is
close.”
“请把组件用手动安装在夹盘内。单击按钮，就关闭夹盘。”
Q242562 “Please press 'Yes' if the installation of components is a success. Please press 'No' when doing
again.”
“已成功安装组件，请单击[是]﹔重试，请单击[否]。”
Q242563 “Please press 'Yes' if detach components by the hand. Please press 'No' when scrap components.”
“手动取下组件，请单击[是]﹔废弃组件，请单击[否]。”
Q242564 “Are components returned ?”
“是否归还组件？”
Q242565 “The components pickuped on the head are returned.”
“归还 Head 上的组件。”
Q242567 “Acquired parameters contain intolerable variations.Do you continue to obtain parameters?
|Selecting'Yes' will repeat measurement approx.20 times as much as specified at the maximum.”
“现在的参数存在不稳定的因素。是否继续取得参数？ |最多进行设置次数 x 20 回左右的
测量动作。”
Q242568 “Acquired parameters contain intolerable variations.Do you continue to obtain parameters?
|Selecting'Yes' will repeat measurement approx.10 times as much as specified at the maximum.”
“当前照明条件下，发生识别错误，是否继续取得动作？|最多测量动作次数是设置次数
x10。”