JUKI贴片机错误代码集合.pdf - 第214页
the data image does not appear a t this point, please turn off t he power supply of yo ur machine and try again. If the data image still does not get displayed after the retry, there is a possibility th at the MCM board …
other.
[Treatment]
‧Please turn off the power supply of your machine and reboot it.
‧If the error occurred after the installation or the version up of the software, you need to re-install
the software.
‧If the treatments above do not work, there is a possibility that MPX board(s) in the machine is
broken. You need to replace it(them) with new ones.
E610048 “Head kind is not defined”
“没有定义的 Head 种类。”
[Cause]
The head type is not correct. Some program versions in the machine may be clashing with each other.
[Treatment]
‧Please turn off the power supply of your machine and reboot it.
‧If the error occurred after the installation or the version up of the software, you need to re-install
the software.
‧If the treatments above do not work, there is a possibility that MPX board(s) in the machine is
broken. You need to replace it(them) with new ones.
E610049 “Laser sensor might be dirty. Please clean the sensor”
“激光传感器可能被弄脏。|请把传感器擦干净。”
[Cause]
A shadow was detected at a position where nothing is supposed to be detected if no nozzle has been
installed and nothing is wrong.
[Treatment]
There is a possibility that the window of the laser sensor is dirty. Please clean the window of the
sensor. You can check the dirt of the window with the following procedures. Select [Manual Control]
from the menu bar, and then select [Control(C)] [Head(H)] [Laser Control(L)]. Select a concerned
laser sensor in 'Control' unit, and then select 'Image displaying' from 'Control Item' frame. By
enabling ON, an image data will be shown.
E610050 “An error occurred in Nozzle posture detection”
“检查吸嘴姿势发生错误。”
[Cause]
A laser error occurred in the Nozzle posture detection by laser prior to a nozzle change.
[Cause]
There is a possibility that the laser recognition unit has a problem. You can check the abnormality of
the unit with the following procedures. Select [Manual Control] from the menu bar, and then select
[Control(C)] [Head(H)] [Laser Control(L)]. Select a concerned laser sensor in 'Control' unit, and then
select 'Image displaying' from 'Control Item' frame. By enabling ON, an image data will be shown. If
the data image does not appear at this point, please turn off the power supply of your machine and try
again. If the data image still does not get displayed after the retry, there is a possibility that the MCM
board in the laser sensor is not installed properly or that the sensor itself is broken. Please turn off the
power supply and examine the installation status of the MCM board in the sensor.
E610051 “The nozzle can not be returned since its posture is abnormal”
“因为吸嘴姿势不对，不能放回吸嘴。”
[Cause]
Nozzle returning got discontinued since a posture of the nozzle exceeded the permissive value during
the Nozzle posture checking by laser prior to a nozzle change.
[Treatment]
Please take the nozzle off manually. Please examine the installation status of a nozzle installed on the
head to find a cause of the error. Treatments to take vary, depending on whether nozzles are set in
the ATC properly or not.
1. If a nozzle rotated against its installation angle to ATC.
There is a possibility that the nozzle rotated during the production. The nozzle might be rotated
manually when the production stopped temporary.
Nozzle rotate every once in a while when a production is done for a long time (over a week) without
changing any nozzles.
If the nozzle rotation occurs during a few-hour production, there is a possibility that the nozzle is
abnormal. You need to replace the nozzle with a new one. If the error occurs regardless the nozzle
types, you need to replace a clamp part with a new one since it may be worn away.
2. If a nozzle did not rotate against its installation angle to ATC.
‧The nozzle shape is abnormal. Please examine if the green plastic part is chipped or not. Also,
please see if there is anything attached to the nozzle.
‧If the installation angle is slanting to a certain side, there is a possibility that the laser measurement
unit is not judging the angle correctly. In this case, the connecting cable between the laser
measurement unit and the servo driver may have a problem. Please take off the cable and re-install it.
‧If the error still occurs, there is a possibility that the MCM board in the laser sensor is not installed
properly or that the MCM board itself is broken. Please turn off the power supply of your machine
and check the installation status of the MCM board in the Laser recognition unit.
E610052 “ATC X coordinate is abnormal”
“X 坐标参数不正确。”
[Cause]
The head could not move to the specified ATC position. Some program versions in the machine may
be clashing with each other.
[Treatment]
‧Please turn off the power supply of your machine and reboot it.
‧If the error occurred after the installation or the version up of the software, you need to re-install
the software.
‧If the treatments above do not work, there is a possibility that MPX board(s) in the machine is
broken. You need to replace it(them) with new ones.
E610053 “An error occurred when detecting the presence of Laser nozzle.”
“检查吸嘴是否存在时发生错误。”
E610054 “Nozzle information (externals size of the nozzle) is not defined.”
“吸嘴信息(吸嘴外形大小)没有被定义。”
E610055 “Because the nozzle is too large, it is not possible to install in the MNLA head.”
“因吸嘴过大，不能安装在 MNLA Head 上。”
E610056 “A large-scale nozzle cannot be installed in the MNLA head.”
“MNLA Head 上，不能安装大型吸嘴。”
E610057 “The error occurred by the installation posture correction of the nozzle.”
“校正吸嘴姿势出错。”
E610058 “The installation posture of the nozzle is abnormal.”
“吸嘴安装姿势错误。”
E610059 “The nozzle is reversely installed in ATC.”
“吸嘴倒立安装在 ATC。”
E610060 “There is a possibility that parts arrive. |The nozzle cannot be returned.”
“吸嘴上可能附有组件。|不能放回吸嘴。”
E610061 “The nozzle is too short. |Please check the nozzle.”
“吸嘴过短。|请检查吸嘴。”
E610062 “Laser sensor might be dirty. |Please clean the sensor.”
“激光传感器可能被弄脏。|请把传感器擦干净。”
E610063 “An error occurred when detecting the laser dirt.”
“检查激光是否干净时，发生错误。”
E610064 “Laser sensor might be dirty. |Please clean the sensor.”
“激光传感器可能被弄脏。|请把传感器擦干净。”
E610065 “An error occurred when detecting the laser dirt.”
“检查激光是否干净时，发生错误。”
E610066 “Z Axis detect Cordinates outof Limit Range.”