JUKI贴片机错误代码集合.pdf - 第154页
E521084 “ Laser Error: (DUP_START) | The firmware found an error whi le rea ding the sensor EEPROM .” “ 激光错误 :(DUP_START) | 固件从传感器 EEPROM 读取数据中发现错误。 ” E521085 “ Laser Error: (NO_EEPROM_SOD) | The firmware found an error …
“激光错误:(NO_ALG) |被要求错误测量方法。”
E521008 “Laser Error:(NO_START) | Eiter the sensor is not connected or there is a hardware error.”
“激光错误:(NO_START) |没有连接传感器，或硬件出错。”
E521010 “Laser Error:(BAD_SENSOR) | The MCM was unable to detect valid sensor data.”
“激光错误:(BAD_SENSOR) |MCM 不能检索正确的传感器数据。”
E521012 “Laser Error:(BAD_EE_VERSION) | The firmware does not recongize the sensor EEPROM
version.”
“激光错误:(BAD_EE_VERSION) |固件不能识别 EEPROM 版本。”
E521013 “Laser Error:(BAD_EE_DATA) | There is an error reading calibration data from the sensor
EEPROM.”
“激光错误:(BAD_EE_DATA) |从传感器 EEPROM 读取校准数据发生错误。”
E521014 “Laser Error:(BAD_EE_SYNC) | There is an error reading calibration data from the sensor
EEPROM.”
“激光错误:(BAD_EE_SYNC) |从传感器 EEPROM 读取校准数据发生错误。”
E521015 “Laser Error:(POWER_LOW) | The MCM detected that the incoming voltage level was below that
required for proper sensor opration.”
“激光错误:(POWER_LOW) |MCM 发现电压下降，导致传感器不能正常运作。”
E521017 “Laser Error:(OVER_CURR) | The MCM detect that power to the sensor was low.”
“激光错误:(OVER_CURR) |MCM 发现电压下降，导致传感器不能正常运作。”
E521060 “Laser Error:(SHORT_BUF) | The communication buffer contained fewer bytes than specified by
the length.”
“激光错误:(SHORT_BUF) |激光数据用通讯缓冲区字节长度偏小。”
E521061 “Laser Error:(LONG_BUF) | The communication buffer contained more bytes than spcified by the
length.”
“激光错误:(LONG_BUF) |激光数据用通讯缓冲区字节长度偏小。”
E521062 “Laser Error:(SHORT_CMD) | The length specified is smaller than expected by the command.”
“激光错误:(SHORT_CMD) |激光命令用通讯缓冲区字节长度偏小。”
E521063 “Laser Error:(LONG_CMD) | The length specified is smaller than expected by the command.”
“激光错误:(LONG_CMD) |激光命令用通讯缓冲区字节长度偏小。”
E521083 “Laser Error:(BAD_CHKSUM) | The firmware found an error while reading the sensor EEPROM.”
“激光错误:(BAD_CHKSUM) |固件从传感器 EEPROM 读取数据中发现错误。”
E521084 “Laser Error:(DUP_START) | The firmware found an error while reading the sensor EEPROM.”
“激光错误:(DUP_START) |固件从传感器 EEPROM 读取数据中发现错误。”
E521085 “Laser Error:(NO_EEPROM_SOD) | The firmware found an error while reading the sensor
EEPROM.”
“激光错误:(NO_EEPROM_SOD) |固件从传感器 EEPROM 读取数据中发现错误。”
E521086 “Laser Error:(BAD_PARM) | An invalid parameter was specified for a command.”
“激光错误:(BAD_PARM) |命令中发现无效的参数。”
E521087 “Laser Error:(BAD_DATA) | Invalid data was detected.”
“激光错误:(BAD_DATA) |发现无效数据。”
E521100 “Laser Error:(UNITS_NOT_SET) | Requested Initialzation was not done.”
“激光错误:(UNITS_NOT_SET) |未初始化状态下，被接受命令错误。”
E521102 “Laser Error:(INVALID_ALG) | The alogrithm specified for the mesurement is invalid.”
“激光错误:(INVALID_ALG) |错误的测量方法。”
E521064 “Laser Error (NO_PART) | The shadow was undetectable during measurement.”
“激光错误:(NO_PART) | 测量中检测不到阴影 “
E521065 “Laser Error:(TOOL_SLOW) | The MCM processor was unable to keep up with the frame rate.”
“激光错误:(TOOL_SLOW) |MCM 处理器不能跟上测量速度。”
E521067 “Laser Error:(ABORTED) | The MCM recived a command that aborted.”
“激光错误:(ABORTED) |MCM 被接受强行停止测量命令。”
E521070 “Laser Error:(ALG_ERR) | The firmware detected a state that should never happen.”
“激光错误:(ALG_ERR) |固件发现了不应该发生的状况。”
E521075 “Laser Error:(PRV_ERR) | During SWEEP_CMD error occuerd during next mesurement.”
“激光错误:(PRV_ERR) |检查端点(Peak)中发现前一次的端点检查错误。”
E521077 “Laser Error:(WIDE_ERR) | The gray-scale edge on the detector did not have enough contrast to
finde actual component edge.”
“激光错误:(WIDE_ERR) |检查组件间距中，发现组件间距不够长。”
E521078 “Laser Error:(SMALL_WIN) | The window parameters specify a window that is samll than 2000
micron.”
“激光错误:(SMALL_WIN) |被指定小于 2000 微米的窗口。”
E521079 “Laser Error:(WIN_BLOCKED) | The entire window is blocked.”
“激光错误:(WIN_BLOCKED) |窗口被赌塞错误。”
E521080 “Laser Error:(LEFT_BLOCKED) | The left edge winow is blocked.”
“激光错误:(LEFT_BLOCKED) |左窗口被赌塞错误。”
E521081 “Laser Error:(RIGHT_BLOCKED) | The right edge window is blocked.”
“激光错误:(RIGHT_BLOCKED) |右窗口被赌塞错误。”
E521082 “Laser Error:(BOTH_BLOCKED) | Both edge of window is blocked.”
“激光错误:(BOTH_BLOCKED) |左右窗口都被赌塞错误。”
E521090 “Laser Error:(TOO_FEW_FRAMES) | Error Caluculating align angle.”
“激光错误:(TOO_FEW_FRAMES) |角度计算出错。”
E521091 “Laser Error:(MIN_OUT_RANGE1) | Error Caluculating align angle.”
“激光错误:(MIN_OUT_RANGE1) |角度计算出错。”
E521092 “Laser Error:(MIN_OUT_RANGE2) | Error Caluculating align angle.”
“激光错误:(MIN_OUT_RANGE2) |角度计算出错。”
E521093 “Laser Error:(MIN_TOO_HIGH) | The Width versus angle curveis too flat.”
“激光错误:(MIN_TOO_HIGH) |因组件太小，不能确定决定组件宽度的角度。”
E521094 “Laser Error:(NO_CUTOFF1) | Error cluculating align angle.”
“激光错误:(NO_CUTOFF1) |角度计算出错。”
E521095 “Laser Error:(NO_CUTOFF2) | Error cluculating align angle.”
“激光错误:(NO_CUTOFF2) |角度计算出错。”
E521096 “Laser Error:(CONST_ANGLE) | Error cluculating align angle.”
“激光错误:(CONST_ANGLE) |角度计算出错。”
E521098 “Laser Error:(SCAN_LIMIT) | The angle exceed apecified angle limit before a minimum was
detected.”
“激光错误:(SCAN_LIMIT) |在界限角度内不能查出决定最小宽度的角度。”
E521099 “Laser Error:(OVERRUN) | Early processing was not completed before sreach for next.”
“激光错误:(OVERRUN) |发现超出限度的错误。”
E521103 “Laser Error:(LOW_BACKGROUND) | The laser intensity was too low during image chack.”
“激光错误:(LOW_BACKGROUND) |检查图像时发现激光强度过低错误。”
E521104 “Laser Error:(BAD_IMAGE_REGION) | Image check region boundaries ware not set properly.”
“激光错误:(BAD_IMAGE_REGION) |图像检查中，发现区域分界线不明确错误。”
E521105 “Laser Error:(IMG_CHK_FAIL) | Image check failed.”
“激光错误:(IMG_CHK_FAIL) |检查图像失败。”