JUKI贴片机错误代码集合.pdf - 第412页
The data is unavailable for optimization. [Deal] Consult the manufacturer. E2934 Al location for parall el pick feeder is abnormal end. " 同时选取进料器优化处理不正常终 止。 " [Cause] The data is unavailable for optimization. […
[Deal]
Check the data (layer and nozzle information).
E2916 Data is incorrect ,so making for pairing placement data.
"不正常数据导致关系预备处理失败。"
[Cause]
A failure was found in the program data.
[Deal]
Correct the data.
E2917 Memory is not enough at optimization feeder priority.
"在保护优先区域的进料器顺序处理过程中出现错误。"
[Cause]
Indicates insufficient free memory space.
[Deal]
Exit from other applications, and retry the process.
E2918 Data is incorrect , so stop processing for circuit repeat.
"不正常数据已经导致电路重复决定失败。"
[Cause]
A failure was found in the program data.
[Deal]
Correct the data.
E2931 Process for make feeder pair of parallel pick is abnormal end.
"同时选取进料器排版预先处理不正常终止"
[Cause]
The data is unavailable for optimization.
[Deal]
Consult the manufacturer.
E2932 Allocation for feeder pair of parallel pick is abnormal end.
"同时选取进料器排版处理不正常终止。"
[Cause]
The data is unavailable for optimization.
[Deal]
Consult the manufacturer.
E2933 Sorting for parallel pick feeder allocate is abnormal end.
"处理资料排架的同时选取进料器排版不正常终止。"
[Cause]
The data is unavailable for optimization.
[Deal]
Consult the manufacturer.
E2934 Allocation for parallel pick feeder is abnormal end.
"同时选取进料器优化处理不正常终止。"
[Cause]
The data is unavailable for optimization.
[Deal]
Consult the manufacturer.
E2935 Can't execute feeder optimization.
"最合适的进料器排版处理不可得。"
[Cause]
The data is unavailable for optimization.
[Deal]
Consult the manufacturer.
E2936 Data renewal is abnormal end.
"进料器更新过程被不正常终止。"
[Cause]
The data is unavailable for optimization.
[Deal]
Consult the manufacturer.
E2941 Sorting for placement layer and same nozzle is abnormal end.
"在贴片层同一吸嘴号处理时出现错误。"
[Cause]
The data is unavailable for optimization.
[Deal]
Consult the manufacturer.
E2942 Memory is not enough at making parallel pick table.
"在保护预备区域的选取表格处理过程中出现错误。."
[Cause]
Indicates insufficient free memory space.
[Deal]
Exit from other applications, and retry the process.
E2943 Making for parallel picking table.
"在处理选取表格决定同时出现错误。"
[Cause]
A simultaneous absorbing feeder pair can not be created.
[Deal]
Consult the manufacturer.
E2944 Memory is not enough at making priority of feeder.
"在保护优先区域的进料器顺序处理过程中出现错误。"
[Cause]
Indicates insufficient free memory space.
[Deal]
Exit from other applications, and retry the process.
E2945 Memory is not enough at making for pairing of placement data.
"在保护贴片区域的处理过程中出现错误。"
[Cause]
Indicates insufficient free memory space.
[Deal]
Exit from other applications, and retry the process.
E2946 ATC Nozzle No.Set %d not set.
"请设置 No. %d 吸嘴。"
[Cause]
An essential nozzle is not allocated to ATC during the MSL setup.
[Deal]
Start the MSL setup to set the placement nozzle.
E2947 Head can't move this position. %s - %d
"不能移动贴装头。%s -- %d"
[Cause]
A feeder is placed on an pick position where the head cannot reach.
[Deal]
Reposition the feeder to where the head can reach.
E2948 Head can't move this position. Stick feeder %s - %d lane %d
"不能移动贴装头。 管 %s -- %d 信道 -- %d"
[Cause]
A stick is placed on an pick position where the head cannot reach.
[Deal]
Reposition the stick to where the head can reach.
E2949 Head can't move this position. Holder %s