JUKI贴片机错误代码集合.pdf - 第451页

E6114 Sett ing of room coefficient is out of range. [Cause] An excessive value w as specified for the redun dant factor. [Deal] Enter a value within the range, 0 to 100. E6250 “ Area cannot be secured. “ " 区域不能被保护。 …

100%1 / 464
E6105 Please select component.
"请选择组件。"
[Cause]
Appears if the number of supplies change button is pressed without a list selected.
[Deal]
Click the part name to highlight it and press the change button or double-click the part name.
E6106 “HLCSETUP.INI file read-in failed. “
"读入 HLCSETUP.INI 文件失败。"
E6109 Enter numeric value.
[Cause]
Appears if no numeric value or any value other than numeric is specified for the feedback option and
the number of redundant factors.
[Deal]
Specify valid values for the feedback option or the number of redundant factors.
E6110 Setting of the number of max loop count is out of range.
[Cause]
An excessive number of the maximum loops was specified for the feedback option.
[Deal]
Enter a value within the range, 1 to 9.
E6111 Setting of target difference time is out of range.
[Cause]
Excessive value was specified for the allowable interval of the feedback option.
[Deal]
Enter a value within the range, 0 to 60 seconds.
E6112 Cannot distribute data with this setting.
[Cause]
For every station, 0 is specified in the balance option.
[Deal]
Check the station to allocate mounting points or application points, and specify the distribution.
E6113 Setting of balance is out of range.
[Cause]
An excessive value was specified for the balance option.
[Deal]
Enter a vale within the range, 0 to 100.
E6114 Setting of room coefficient is out of range.
[Cause]
An excessive value was specified for the redundant factor.
[Deal]
Enter a value within the range, 0 to 100.
E6250 “Area cannot be secured. “
"区域不能被保护。"
E6251 “INI file cannot be read. “
"不能读 INI 文件。"
E6252 “Distributed data cannot be read. “
"不能读分配数据。"
E6253 “Data combining failed. “
"数据结合失败。"
E6254 “Combining of data failed because data are mutually exclusive. “
"由于数据相互排斥数据结合失败。"
E6255 “Combined data cannot be output. “
"不能输出组合数据。"
E6300 “Setting of number of programs etc. failed. “
"设置程序数量等失败。"
E6350 Area cannot be secured.
"区域不能被保护。"
[Cause]
Allocating the memory for EPU was failed. Allocating the memory for G3h and G3N was failed.
[Deal]
Exit from other applications and retry the process.
E6351 File read failed.
"不能读预定程序目录。"
[Cause]
Loading files, G3H and GXL, was failed. Insufficient free space on the memory or any failure on the
disk is suspected.
[Deal]
Run the "Scan-disk" to check the disk. Exit from other applica
tions and retry installation.
E6352 “Data before distribution cannot be read. “
"不能读分配前的数据。"
E6353 “Distribution option cannot be read. “
"不能读分配选项。"
E6354 Reference table cannot be read.
"不能读资料表。"
[Cause]
Loading files, OPTIM.INI and CYCLE.INI. It is suspected that the installation was failed or any
failure occurred on the disk.
[Deal]
Run the "Scan-disk" to check the disk. Exit from other applications and retry installation.
E6355 “Station information cannot be read. “
"不能读位置信息。"
E6356 Resource data cannot be read.
"不能读资源数据。"
[Cause]
Loading a files HLCSETUP.INI. It is suspected that the installation was failed or any failure occurred
on the disk.
[Deal]
Run the "Scan-disk" to check the disk. Exit from other applications and retry installation.
E6357 “Permanent data cannot be read. “
"不能读永久数据。"
E6358 “Station order conflicts with the optimization that was excuted. “
"优化的位置顺序有冲突."
E6400 “Component in program and permanent component are improperly positioned. “
"在程序中的组件和永久性组件位置不正确."
E6402 “PWB data is not completed. “
"基板数据不完全。"
E6403 Component data are incomplete. (No.%d)
"贴片数据不完全。"
[Cause]
The mounting data is incomplete.
[Deal]