JUKI贴片机错误代码集合.pdf - 第104页
[Cause] The production can not get start ed because PWBs are on the conv eyors on b oth sides when starting the production. [Treatment] Please remove the PWBs from th e conveyors by pressing OK butt on , and then press S…
E500602 “An error occurred while performing Yc table end check. Code : %d”
“结束 Yc 支撑台检查时，发生错误。|代码 : %d”
E500603 “An error occurred while performing axis end check. Code : %d”
“结束轴移动检查时，发生错误。|代码 : %d”
E500605 “An error occurred when disposing a component”
“废弃组件发生错误。”
[Cause]
This error occurs if the component present check at a component disposal action gets an error when
starting a production.
[Treatment]
Pressing OK button will abort the process. In this case, the production will not be executed.
E500700 “An error occurred while Auto. PWB Width Alignment Control. | The process gets discontinued”
“自动调整基板宽度发生错误。|退出操作。”
[Cause]
This error occurs if an error occurs or an action did not take place properly while Auto. PWB Width
Alignment Control.
[Treatment]
Pressing OK button will abort the process. If a particular reason (Home returning has not been
complete, etc.) why Auto. PWB Width Alignment Control can not be executed is given, please
perform any means to get rid of the factor that stops Auto. PWB Width Alignment Control. If any
particular reasons are not given, please, check the action of Auto. PWB Width Alignment Control by
Manual control .
E500701 “Para error. PWB Width Alignment Control occurred”
“自动调整基板宽度参数错误”
[Cause]
This error occurred if an entered value to be defined by Enter key is wrong when performing Auto.
PWB Width Alignment Control.
[Treatment]
Please check the entered value.
E500710 “An error occurred while Auto. BOC mark.|The process gets discontinued.”
“识别 BOC 标记发生错误|退出操作。”
E500711 “Param error|BOC mark occurred.”
“识别 BOC 标记参数错误”
E500800 “A PWB is detected within the conveyors of both stations. Please remove the PWB”
“两个站台内的传送轨道上，发现基板。|请取下基板。”
[Cause]
The production can not get started because PWBs are on the conveyors on both sides when starting
the production.
[Treatment]
Please remove the PWBs from the conveyors by pressing OK button, and then press START key
again.
E500801 “A PWB is detected within the conveyor of the Left station. Please remove the PWB”
“左边站台的传送轨道上，发现基板。|请取下基板。”
[Cause]
The production can not get started because a PWB is on the conveyor on left side when starting the
production.
[Treatment]
Please remove the PWBs from the conveyors by pressing OK button, and then press START key
again.
E500802 “A PWB is detected within the conveyor of the Right station. Please remove the PWB”
“右边站台的传送轨道上，发现基板。|请取下基板。”
[Cause]
The production can not get started because a PWB is on the conveyor on right side when starting the
production.
[Treatment]
Please remove the PWBs from the conveyors by pressing OK button, and then press START key
again.
E500803 “A PWB is detected within the conveyor.|Please remove the PWB.”
“在传送轨道上发现基板。|请取下基板。”
E500900 “The connection with HLC is on-line. The production is not available with the currently selected
production program created by the machine”
“HLC 处于联机状态。|不能以当前被选用的主机程序进行生产。”
[Cause]
The connection between your machine and HLC is set to ON in the Setup. The currently selected
production program was created by the machine. Therefore, its production can not get started.
[Treatment]
Please cut off the connection between your machine and HLC in the Setup or read in another
production program.
E500901 “It is not connected to HLC. The production is not available with the currently selected production
program created by HLC”
“没有连接 HLC。|不能以现在被选用的 HLC 程序进行生产。”
[Cause]
A production program that was created by HLC was read in and its production is about to get started
with the connection between your machine and HLC being OFF.
[Treatment]
Please enable the connection between your machine and HLC in the Setup or read in another
production program.
E500902 “Online switch is not effective to the Setup data though the connection with HLC is turning on”
“设置数据上已经选择了连接 HLC，但联机按钮为无效。”
[Cause]
Online switch is not available while the connection between your machine and HLC is ON in the
Setup data.
[Treatment]
Please cut off the connection between your machine and HLC in the Setup or enable the online
switch.
E501000 “MTC Move Failed”
“因 MTC 运转出错，停止生产。”
[Cause]
This error occurs when an error occurs from MTC during a production.
[Treatment]
Please turn off the power supply of MTC and examine it.
E501010 “MTC Power is Off. Please Power On”
“MTC 电源被关闭，|请打开电源。”
[Cause]
This error occurs if MTC is not ON when starting a production.
[Treatment]
Please turn on the power supply of MTC and press OK button. Pressing Cancel button will have you
back to the status that is before pressing START key.
E501011 “MTC Emergency Switch is Pressed. Please Release the Switch”
“MTC 被处于紧急停止状态，|请解除紧急按钮。”
[Cause]
This error occurs if the Emergency Switch of MTC has been pressed when starting a production.
[Cause]
Please press OK button after disabling the Emergency Switch. Pressing Cancel button will have you
back to the status that is before pressing START key.
E501012 “MTC is No Original”
“MTC 未完成返回原点。”