JUKI贴片机错误代码集合.pdf - 第65页
There is no head available. [Treatment] Please set any ne cessary heads to “ use ” in the Use unit in Machin e Setup. E301024 “ Selected device is disable. | Pl ease reselect other device on H OD ” “ 被选设备是不能使用设备。 | 请重新选 …
device selected by HOD.
[Treatment]
Please reselect a device available.
E301018 “Selected device is not installed. | Please reselect other device on HOD”
“被选设备尚未安装。|请重新选择其它设备。”
[Cause]
Since the device selected by HOD has not been installed (the installation of the device is not set in the
option of MS parameter), you can go into the teaching mode.
[Treatment]
Please reselected a device available.
E301019 “Return to home has not yet been completed”
“尚未完成原点返回。”
[Cause]
The axis has not yet returned to home.
[Treatment]
Please perform the Return to home with ORIGIN switch.
E301020 “MTC power off”
“没有打开 MTC 电源。”
[Cause]
Failed to draw MTC shuttle out when teaching MTC shuttle pick position to the machine since MTS
was not ON.
[Treatment]
Please turn on the power supply of MTC.
E301021 “MTC offline”
“MTC 处于脱机状态。”
[Cause]
Failed to draw the MTC shuttle out when teaching MTC shuttle pick position to the machine since
MTC was not online.
[Treatment]
Please make MTC online.
E301022 “File I/O Error|Error code:%02d|File name:%s”
“文件 I/O 错误|错误代码:%02d|文件名:%s”
E301023”There is no installed head”
“不存在可用 Head。”
[Cause]
There is no head available.
[Treatment]
Please set any necessary heads to “use” in the Use unit in Machine Setup.
E301024 “Selected device is disable. | Please reselect other device on HOD”
“被选设备是不能使用设备。|请重新选择别的设备。”
[Cause]
Since the device selected by HOD is non-use device (it is set to “not use” in the Use unit in Machine
Setup), you can not go into the teaching mode.
[Treatment]
Please select a device available.
E301025 “MTC is disable”
“MTC 不能使用。”
[Cause]
MTC can not be controlled since it is non-use device (it is set to “not use” in the Use unit in Machine
Setup)
[Treatment]
Please set the MTC to “use” in the Use unit in Machine Setup.
E301026 “Servo is in the free state”
“伺服处于未使用状态。”
[Cause]
The axis could not move since the servo is not locked.
[Treatment]
Please lock the servo with S-FREE switch.
W301027 “Teached data is invaled”
“示教数据无效。”
[Cause]
When an error caused by 'out of the measurement range' occurred while learning the Z axis coordinate
by HMS (when “---” is shown for Z in the teaching dialog), you can not learn the coordinate even if
you hit the enter key on HOD. The coordinate also can not be learned when other error occur while
teaching.
[Treatment]
When you learn the coordinate of Z axis by HMS, please make sure that the coordinate is within the
measurement range.
E301028 “Length of the nozzle is too short. | Please check the nozzle”
“吸嘴长度过短。|请检查吸嘴。”
[Cause]
The laser detection height of nozzle, that was automatically learned, was too high. A nozzle which is
shorter by over 1mm than a standard nozzle was detected. The nozzle length might be too short.
[Treatment]
Please check the nozzle length. [Cause]
E301029 “Vacuum is not ON.”
“没有起动真空器。”
E301032 “MTC is in the supply state”
“MTC 补充状态。”
[Cause]
MTC can not be controlled since it is in the Supply (component change) state.
[Treatment]
Please make MTC a normal status.
E301033 “Password is different from a predetermined one.”
“密码不一致。”
W301034 “The Height of nozzle exceeds a regulated value.%7.4lf mm”
“吸嘴高度超过规定值。%7.4lf mm”
E301035 “MTS is disable”
“不能使用 MTS。”
[Cause]
MTS can not be controlled since it is non-use device (it is set to “not use” in the Use unit in Machine
Setup)
[Treatment]
Please set the MTS to “use” in the Use unit in Machine Setup.
E301036 “MTS power off”
“没有打开 MTS 电源。”
[Cause]
Failed to draw the MTS tray out since the MTS was not ON.
[Treatment]
Please turn on the power supply of MTS.
E301037 “MTS offline”
“MTS 处于脱机状态。”
[Cause]
Failed to draw the MTS tray out since the MTS was not online.
[Treatment]
Please make MTS online.