JUKI贴片机错误代码集合.pdf - 第162页
E601025 “ Axis Driver:| Failed amp disable.(ZT4) ” “ 中断 AMP 失败。 (ZT4) ” E601030 “ Axis Driver:| Fail ed alarm clear.(XY) ” “ 排除警报失败。 (XY) ” E601031 “ Axis Driver:| Failed alarm clear.(Yc) ” 排除警报失败。 (Yc) ” E601032 “ Axis …
E600036 “Axis Driver:| The velocity error exceeded the limit.|(Check the power supply for the possibilities of
low power supply voltage.)”
“速度误差超过界限。|(可能电压不足，请检查电压。)”
E600040 “Axis Driver:| Coordinates exceed a movable range.”
“超出正常移动范围。”
E600042 “Axis Driver:| Cannot continue operation because of cover open.”
“因为安全盖被打开,所以不能运行。”
E601001 “Axis Driver:| Failed servo power on.”
“伺服电源的打开失败。”
E601010 “Axis Driver:| Failed amp enable.(XY)”
“启动伺服驱动器失败。(XY)”
E601011 “Axis Driver:| Failed amp enable.(YC)”
“启动伺服驱动器失败。(YC)”
E601012 “Axis Driver:| Failed amp enable.(ZT1)”
“启动伺服驱动器失败。(ZT1)”
E601013 “Axis Driver:| Failed amp enable.(ZT2)”
“启动伺服驱动器失败。(ZT2)”
E601014 “Axis Driver:| Failed amp enable.(ZT3)”
“启动伺服驱动器失败。(ZT3)
E601015 “Axis Driver:| Failed amp enable.(ZT4)”
“启动伺服驱动器失败。(ZT4)”
E601020 “Axis Driver:| Failed amp disable.(XY)”
“中断 AMP 失败。(XY)”
E601021 “Axis Driver:| Failed amp disable.(Yc)”
“中断 AMP 失败。(Yc)”
E601022 “Axis Driver:| Failed amp disable.(ZT1)”
“中断 AMP 失败。(ZT1)”
E601023 “Axis Driver:| Failed amp disable.(ZT2)”
“中断 AMP 失败。(ZT2)”
E601024 “Axis Driver:| Failed amp disable.(ZT3)”
“中断 AMP 失败。(ZT3)”
E601025 “Axis Driver:| Failed amp disable.(ZT4)”
“中断 AMP 失败。(ZT4)”
E601030 “Axis Driver:| Failed alarm clear.(XY)”
“排除警报失败。(XY)”
E601031 “Axis Driver:| Failed alarm clear.(Yc)”
排除警报失败。(Yc)”
E601032 “Axis Driver:| Failed alarm clear.(ZT1)”
“排除警报失败。(ZT1)”
E601033 “Axis Driver:| Failed alarm clear.(ZT2)”
“排除警报失败。(ZT2)”
E601034 “Axis Driver:| Failed alarm clear.(ZT3)”
“排除警报失败。(ZT3)”
E601035 “Axis Driver:| Failed alarm clear.(ZT4)”
“排除警报失败。(ZT4)”
E601040 “Axis Driver:| Failed CAL.BLOCK mark Recognition. (L-OCC)”
“识别校准块标记失败。(L-OCC)”
E601041 “Axis Driver:| Failed CAL.BLOCK mark Recognition. (R-OCC)”
“识别校准块标记失败。(R-OCC)”
E601042 “Axis Driver:| Return to origin non-completion.”
“尚未完成返回原点。”
E601043 “Axis Driver:| Servo free.”
“伺服处于不使用状态。”
E601044 “Axis Driver:| XH-axis Irregular Position.”
“LSC 位置不对。”
E601045 “Axis Driver:| Please move LSC to the sensor position.”
“请把 LSC 移到传感器位置。”
E601046 “Axis Driver:| LSC communication error.”
“LSC 通讯失败。”
E601047 “Axis Driver:| The state of can the use of the XH-axis it is improper.”
“XH 轴的使用状态不对。”
E602110 “Axis Driver:| X-axis parameter error.”
“X 轴参数错误。”
E602210 “Axis Driver:| Y-axis parameter error.”
“Y 轴参数错误。”
E602310 “Axis Driver:| XR-axis parameter error.”
“XR 轴参数错误。”
E602410 “Axis Driver:| YC-axis parameter error.”
“YC 轴参数错误。”
E602510 “Axis Driver:| YR-axis parameter error.”
“YR 轴参数错误。”
E602112 “Axis Driver:| X-axis failed originating.”
“X 轴回原点失败。”
E602212 “Axis Driver:| Y-axis failed originating.”
“Y 轴回原点失败。”
E602312 “Axis Driver:| XR-axis failed originating.”
“XR 轴回原点失败。”
E602412 “Axis Driver:| YC-axis failed originating.”
“YC 轴回原点失败。”
E602512 “Axis Driver:| YR-axis failed originating.”
“YR 轴回原点失败。”
E602113 “Axis Driver:| X-axis error.|Servo power is OFF.”
“X 轴错误。|伺服电源被关闭状态。”
E602213 “Axis Driver:| Y-axis error.|Servo power is OFF.”
“Y 轴错误。|伺服电源被关闭状态。”
E602313 “Axis Driver:| XR-axis error.|Servo power is OFF.”
“XR 轴错误。|伺服电源被关闭状态。”
E602413 “Axis Driver:| YC-axis error.|Servo power is OFF.”
“YC 轴错误。|伺服电源被关闭状态。”
E602513 “Axis Driver:| YR-axis error.|Servo power is OFF.”
“YR 轴错误。|伺服电源被关闭状态。”