JUKI贴片机错误代码集合.pdf - 第84页
“ YES ” button will abort the process. “ NO ” button will resume the process. Q317041 “ Is the tray of MTS stored? ” “ 可能取出托盘。 | 是否储存 MTS 托盘？ ” [Cause] “ Exit MTS control screen ” was chosen with MTS t ray was drawn out.…
“OK” will abort the process.
E316601 “DTS is in the supply state.”
“DTS处于补充状态。”
E316602 “The cover of DTS opens.”
“DTS 机箱盖被打开。”
Q317001 “Exit manual control. Reset I/O?”
“退出手动控制。|是否重设 I/O ？”
[Cause]
This message appears when you choose to exit the Manual control. You are asked if to set each I/O in
the safety direction
[Treatment]
“YES” button will sets I/O in the safety direction. “NO” button will discontinue to exit the Manual
control.
Q317011 “Return to home has not yet been completed. Return to home?”
“尚未结束原点返回。|是否执行原点返回？”
[Cause]
The axis has not yet been returned to home. You are asked if you want to perform the Home
returning.
[Treatment]
“YES” button will return the axis to home, and continue the process. “NO” button will not return the
axis to home, and continue the process.
Q317021 “Cannot return component. Trash component?”
“不能归还组件。|是否废弃组件？”
[Cause]
A component was detected in the Component presence checking that is performed when returning
nozzle to ATC. The component can not be returned since its pick position is unknown. You are asked
if the component can be disposed.
[Treatment]
“YES” button will dispose the component at a disposal position. “NO” button will move the head to
the waiting position for nozzle removal, and request for a manual component removal.
Q317031 “Do you interrupt process?”
“是否停止处理？”
[Cause]
STOP switch was pressed. You are asked if to abort the process.
[Treatment]
“YES” button will abort the process. “NO” button will resume the process.
Q317041 “Is the tray of MTS stored?”
“可能取出托盘。|是否储存 MTS 托盘？”
[Cause]
“Exit MTS control screen” was chosen with MTS tray was drawn out.
[Treatment]
“YES” will store the tray into MTS and exit the screen. ”NO” will exit the screen with MTS tray is
drawn out of MTS.
I318001 “Remove the component from %s”
“请取下%s 上的组件。”
[Cause]
The nozzle could not be returned to ATC since something, such as a component, was on the nozzle.
[Treatment]
Please remove the component off the head manually.
I318011 “Set online for MTC”
“请设置 MTC 联机状态。”
[Cause]
Failed to draw shuttle out from MTC since MTC was not online.
[Treatment]
Please make MTC online.
I318021 “Set online for MTS”
“请设置 MTS 联机状态。”
[Cause]
MTS was not online.
[Treatment]
Please make MTS online.
I318022 “Please close the door of MTS”
“请关闭 MTS 的机箱门。”
[Cause]
Failed to draw a tray out from MTS since MTS door was open.
[Treatment]
Please close the MTS door.
I318023 “Remove the PWB on Conveyor”
“请取下搬运轨道上的基板。”
[Cause]
A PWB was detected on the conveyor.
[Treatment]
Please removed the PWB on the conveyor.
I318024 “Remove the handknob.”
“请取下摇把。”
E397001”Memory allocation error”
“分配内存发生错误”
[Cause]
The working space can not be saved.
[Treatment]
Please add some more memory available to save the working space.
E397002”Shared memory open error”
“打开共享内存发生错误”
[Cause]
The shared memory could not be opened.
[Treatment]
Please contact our technical service dept. for information.
E397011”Return to home has not yet been completed”
“未结束返回原点。|请确认一下搬运轨道上是否没有 Head。|请确认一下基板传送是否正
常。”
[Cause]
The axis can not move until Home returning has been complete.
[Treatment]
Please press the ORIGIN switch to perform Home returning.
E397012 ”Servo is in the free state”
“伺服处于未使用状态。|请确认一下搬运轨道上是否没有 Head。|请确认一下基板传送是
否正常。”
[Cause]
The axis could not move since the servo is in the free status.
[Treatment]
In order to move the axis, please press the Servo Free switch to lock the servo.
E398001 “Memory allocation error”
“分配内存错误”
[Cause]
The working space can not be saved.