JUKI贴片机错误代码集合.pdf - 第76页
“ 吸嘴信息 (%s) 已经存在。 | 是否覆盖保存 ？ ” Q302018 “ Please check if the PWB is clamp ed.|Would you li ke to continue ? ” “ 请检查一下基板是否已经被固定。 | 是 否继续？ ” Q302019 “ Delete the nozzle data[ %s ].|Is that OK ? ” “ 删除被选吸嘴数据 [ %s ] 。 | 是否继续…
Q302012 “Move Z axis to where nozzles are taken off. | Is that OK?”
“Z 轴移到卸下吸嘴位置。|请检查一下是否受到送料器台架的干扰。|是否继续？”
[Cause]
A nozzle installation error of ATC nozzle allocation occurred. You are asked if to move the head to
the nozzle removal position.
[Treatment]
“Yes” button will move the axis to the nozzle removal position, and continue the process.
“NO” button will not move the axis to the nozzle removal position, but continue the process.
Q302013 “Return Z axis to Laser height position. | Is that OK?”
“Z 轴返回激光高度位置。|是否继续？”
[Cause]
When a nozzle installation error of ATC nozzle allocation occurred, you are asked if to move the
head to the laser height after the head gets to the nozzle removal position.
[Treatment]
“YES” button will move the head to the laser height, and continue the process.
“NO” button will not move the head to the laser height but continue the process.
Q302014 “Please check if the backup plate is lifted up enough. | It may be a little hard to see pins when the
plate is not lifted up. | Would you like to continue?”
“请检查一下支撑台是否已台升。|如果没有被台升，就不好辨认。|是否继续？”
[Cause ]
When teaching the ref. pin position to the machine, backup plate is checked to see if it is open or not,
and then you are asked if you continue the process.
[Treatment]
“YES” button will continue the process.
“NO” button will abort the process.
Q302015 “There may be some units with ON state. | Would you like to initialize these units?”
“在机器设置中，有些单元被处于驱动状态。|是否初始化这些单元？”
[Cause]
If a driving unit which can possibly be an obstruct is detected when executing the conveying control
of the Mechanical Setup, you are asked if to initialize the unit.
[Treatment]
“YES” button will initialize concerned unit(s) and resume the process.
“NO” button will not control the concerned unit(s) and resume the process.
Q302016 “Execute auto-teaching ?”
“是否执行自动示教？”
Q302017 “The nozzle data(%s) has already been registered.|Do you want to overwrite the data ?”
“吸嘴信息(%s)已经存在。|是否覆盖保存？”
Q302018 “Please check if the PWB is clamped.|Would you like to continue ?”
“请检查一下基板是否已经被固定。|是否继续？”
Q302019 “Delete the nozzle data[ %s ].|Is that OK ?”
“删除被选吸嘴数据[ %s ]。|是否继续?”
Q302020 “The offset position with the preserved MTS class is used.|Is that OK ?”
“使用保存过的 MTS 安装偏差位置。|是否继续？”
I303000 “Return to home of %s”
“执行%s 的原点返回。”
[Cause]
Z axis and the Theta axis of the ? head will return to Home.
[Treatment]
Please hit the “OK” button.
I303001”Nozzle is removed from %s to ATC”
“卸下%s 的吸嘴。”
[Cause]
There is a need to remove the nozzle from the ? head.
[Treatment]
Please press “OK” button. If you hit the “OK” button, it will return the nozzle on the ? head to ATC.
I303002 “Return Z axis to Laser height position.”
“把 Z 轴高度返回到激传感器高度。 “
I304000 “Set online for MTC”
“请连接 MTC。”
[Cause]
Failed to draw tray out from MTC when teaching in the MTC shuttle pick position setting since MTC
was not online.
[Treatment]
Please make MTC online.
I304001 “Remove the nozzle from %s”
“请取下%s 的吸嘴。”
[Cause]
The nozzle could not be returned automatically since a nozzle installation error occurred while
automatically learning the ATC nozzle allocation. Please remove the nozzle on the ? head manually.
[Treatment]
Please remove the nozzle and then hit the “OK” button.
I304002”A nozzle of %s is removed and return to %s of ATC”
[Cause]
The nozzle could not be returned automatically.
[Treatment]
Please remove a nozzle on the head manually and return it to the of ATC.
I304003 “Set online for MTS”
“请连接 MTS。”
[Cause]
MTS was not online.
[Treatment]
Please make MTS online.
I304004 “Please close the door of MTS”
“请关闭 MTS 机箱门。”
[Cause]
Failed to draw the MTS tray out since the MTS door was open.
[Treatment]
Please close the MTS door.
I304005 “Lift a head to the highest position manually.”
手动提高 Head 的高度。”
E316001 “Memory allocation error”
“内存分配错误。”
[Cause]
The working space can not be saved.
[Treatment]
Please add some more memory available to save the working space.
E316002 “Shared memory open error”
“打开共享内存错误。”
[Cause]
The shared memory could not be open.
[Treatment]
Please shut down the your machine and re-start it.
E316011 “There is no input character”
“没有输入字符。”
[Cause]