JUKI贴片机错误代码集合.pdf - 第24页
E192005 “ A system error occurred.|Failed in the opening of t he mail of t he production cont rol.|Detail code=0x%08X ” “ 发生系统错误。 | 打开生产管理邮件失 败。 | 详细代码 =0x%08X ” E192006 “ A system error occurred.|Failed in the opening o…
Q191304 “The template does not have enough contrast. | Would you like to take the teaching results in?”
“因模板的对比度不够，标记识别不完整。|是否获取示教结果？”
[Cause]
The user defined template does not have enough contrast.
用户定义模板没有明显的对比度。
[Treatment]
Please re-teach other user defined templates to the machine.
请选择其它用户定义模板再示教。
If you do not have other user defined templates, current template will be taken in although the
template may not be recognized correctly.
没有其它用户定义模板时，即使识别不正确，也要读取结果。
Q191305 “The template has no features. | Would you like to take the teaching results in?”
“模板上无特征。|是否获取示教结果？”
[Cause]
The specified user defined template does not have any notable patterns.
被指定的用户定义模板上无特别图案。
[Treatment]
Please re-teach other user defined templates to the machine.
请选择其它用户定义模板再示教。
If you do not have other user defined templates, current template will be taken in although the
template may not be recognized correctly.
没有其它用户定义模板时，即使识别不正确，也要读取结果。
E192000 “A system error occurred.|Failed in create of the mail object.|Detail code=0x%08X”
“发生系统错误。|建立邮件对象失败。|详细代码=0x%08X”
E192001 “A system error occurred.|Failed in the opening of the mail of the application-manager.|Detail
code=0x%08X”
“发生系统错误。|打开程序管理邮件失败。|详细代码=0x%08X”
E192002 “A system error occurred.|Failed in the mail transmission to the application-manager.|Detail
code=0x%08X”
“发生系统错误。|给程序管理发送邮件失败。|详细代码=0x%08X”
E192003 “A system error occurred.|Failed in the mail reception.|Detail code=0x%08X”
“发生系统错误。|接受邮件失败。|详细代码=0x%08X”
E192004 “A system error occurred.|Sending station ID is abnormal.|ID= %d”
“发生系统错误。|发送站点 ID 错误。|ID= %d”
E192005 “A system error occurred.|Failed in the opening of the mail of the production control.|Detail
code=0x%08X”
“发生系统错误。|打开生产管理邮件失败。|详细代码=0x%08X”
E192006 “A system error occurred.|Failed in the opening of the shared memory.|Detail code=0x%08X”
“发生系统错误。|打开共享内存失败。|详细代码=0x%08X”
E192007 “A system error occurred.|Failed in the close of the shared memory.|Detail code=0x%08X”
“发生系统错误。|关闭共享内存失败。|详细代码=0x%08X”
E192008 “A system error occurred.|Failed in the acquisition of the computer name.|Detail code=%d”
“发生系统错误。|取得计算器名称失败。|详细代码=%d”
W192100 “Retry List message file (%s) cannot be opened.”
“不能打开重试列表信息文件(%s)。”
第二章 组件测量
[组件测量、跟踪、Verify 检查、视觉识别、LSC 识别、照明确定、共面性检查、识别送料器台架、标记数据库]
E240000 “The axis cannot be moved”
“轴不能移动。”
[Cause]
The axis could not move for some reason.
轴不能移动。
[Treatment]
Please check and see if the axis can move properly with Manual control.
请以“手动控制”检查轴能不能正常活动。
E240001 “The axis cannot be moved to escape point”
“不能移到轴等待位置。”
[Cause]
You could not move the axis to the Escape point.
轴不能移动到等待位置。
[Treatment]
Please check and see if the axis can move properly with Manual control.
请以“手动控制”检查轴能不能正常活动。
E240002 “Yc table cannot be moved”
“Yc 支撑台不能移动。”
[Cause]
You could not move the Yc table.
Y 方向中心支撑台不能移动。
[Treatment]
Please check and see if the Yc table can move properly with Manual control.
请以“手动控制”检查 Yc 支撑台能不能正常活动。
E240003 “The axis margin out of range. It is not possible to operation”
“因超过范围，轴不能移动。”
[Cause]
You could not move the axis since it went out of its movable range.
因为轴移动位置超出活动范围，所以不能移到位。
[Treatment]
Please check and see if its coordinates are correct.
请检查坐标。
E240004 “The interrupt which was not able to operate was detected. | The trace is ended”
“发现不能动作的阻碍。|停止跟踪。”
[Cause]
The process was forcibly aborted since an interruption, such as axis alarm and Emergency STOP, that
stops every kind of actions was detected.
[Treatment]
Please check and see if any alarms occurred, and deal with causes of the alarm.
E240005 “The area sensor was detected. | Please remove the sensor reaction factor”
“因范围传感器发现错误而暂停。|请排除故障。”
[Cause]
Tracing got paused since the area sensor detected something.
[Treatment]
Please removed a factor detected by the sensor, and resume tracing.
E240006 “The feeder float sensor was detected. | Please remove the sensor reaction factor”
“发现传送带浮动。|请矫正传送带。”
[Cause]
Tracing got paused since the feeder float sensor detected something.
[Treatment]
Please removed a factor detected by the sensor, and resume tracing.
E240007 “Input is mistake”
“输入错误。”
[Cause]