JUKI贴片机错误代码集合.pdf - 第105页

[Cause] A production program that was cr eated by HLC was read in and it s production is about to get started with the connection between your machine and HLC being OFF. [Treatment] Please enable the connection be tween …

100%1 / 464
[Cause]
The production can not get started because PWBs are on the conveyors on both sides when starting
the production.
[Treatment]
Please remove the PWBs from the conveyors by pressing OK button, and then press START key
again.
E500801 “A PWB is detected within the conveyor of the Left station. Please remove the PWB”
“左边站台的传送轨道上，发现基板。|请取下基板。”
[Cause]
The production can not get started because a PWB is on the conveyor on left side when starting the
production.
[Treatment]
Please remove the PWBs from the conveyors by pressing OK button, and then press START key
again.
E500802 “A PWB is detected within the conveyor of the Right station. Please remove the PWB”
“右边站台的传送轨道上，发现基板。|请取下基板。”
[Cause]
The production can not get started because a PWB is on the conveyor on right side when starting the
production.
[Treatment]
Please remove the PWBs from the conveyors by pressing OK button, and then press START key
again.
E500803 “A PWB is detected within the conveyor.|Please remove the PWB.”
“在传送轨道上发现基板。|请取下基板。”
E500900 “The connection with HLC is on-line. The production is not available with the currently selected
production program created by the machine”
“HLC 处于联机状态。|不能以当前被选用的主机程序进行生产。”
[Cause]
The connection between your machine and HLC is set to ON in the Setup. The currently selected
production program was created by the machine. Therefore, its production can not get started.
[Treatment]
Please cut off the connection between your machine and HLC in the Setup or read in another
production program.
E500901 “It is not connected to HLC. The production is not available with the currently selected production
program created by HLC”
“没有连接 HLC。|不能以现在被选用的 HLC 程序进行生产。”
[Cause]
A production program that was created by HLC was read in and its production is about to get started
with the connection between your machine and HLC being OFF.
[Treatment]
Please enable the connection between your machine and HLC in the Setup or read in another
production program.
E500902 “Online switch is not effective to the Setup data though the connection with HLC is turning on”
“设置数据上已经选择了连接 HLC，但联机按钮为无效。”
[Cause]
Online switch is not available while the connection between your machine and HLC is ON in the
Setup data.
[Treatment]
Please cut off the connection between your machine and HLC in the Setup or enable the online
switch.
E501000 “MTC Move Failed”
“因 MTC 运转出错，停止生产。”
[Cause]
This error occurs when an error occurs from MTC during a production.
[Treatment]
Please turn off the power supply of MTC and examine it.
E501010 “MTC Power is Off. Please Power On”
“MTC 电源被关闭，|请打开电源。”
[Cause]
This error occurs if MTC is not ON when starting a production.
[Treatment]
Please turn on the power supply of MTC and press OK button. Pressing Cancel button will have you
back to the status that is before pressing START key.
E501011 “MTC Emergency Switch is Pressed. Please Release the Switch”
“MTC 被处于紧急停止状态，|请解除紧急按钮。”
[Cause]
This error occurs if the Emergency Switch of MTC has been pressed when starting a production.
[Cause]
Please press OK button after disabling the Emergency Switch. Pressing Cancel button will have you
back to the status that is before pressing START key.
E501012 “MTC is No Original”
“MTC 未完成返回原点。”
[Cause]
This error occurs if MTC Home returning has not been complete yet when starting a production.
[Treatment]
OK button : Performs MTC Home returning.
Cancel button : Will have you back to the status that is before pressing START key.
E501013 “MTC is off-line Condition. Please change to on-line”
“MTC 处于脱机状态，|请连接 MTC。”
[Cause]
This error occurs if MTC is Offline when starting a production.
[Treatment]
Please put MTC in online status and press OK button. Pressing Cancel button will have you back to
the status that is before pressing START key.
E501014 “MTC is Door Open Condition. Please Close Cover”
“MTC 的门被打开，|请关上门。”
[Cause]
This error occurs if MTC door is open when starting a production.
[Treatment]
Please close the MTC door then press OK button. Pressing Cancel button will have you back to the
status that is before pressing START key.
E501015 “MTC is Cover Open Condition. Please Close Cover”
“MTC 机盖被打开，|请关闭机盖。”
[Cause]
This error occurs if MTC cover is open when starting a production.
[Treatment]
Please close the MTC cover then press OK button. Pressing Cancel button will have you back to the
status that is before pressing START key.
E501016 “MTC is Error Condition”
“MTC 发生错误。”
[Cause]
This error occurs if MTC is in an error status when starting a production.
[Treatment]
Please turn off the power supply of MTC and examine it.
E501017 “MTC is Change Component Condition. Please Release the Change Condition”
“MTC 处于交换组件状态，|请解除交换状态。”
[Cause]
This error occurs if MTC is in a status where MTC needs a component change when starting a