JUKI贴片机错误代码集合.pdf - 第152页
Q514601 ” May I abandon MTS parts? ” “ 是否废弃 MTS 组件？ ” I514802 “ It is temporary stop by the part protection.|Please detach part s .” “ 为保护组件暂停。 | 请取下组件。 ” E515001 “ DTS abnormal operat i on was generated .” “ DTS 运转异常。 ”…
W513408 “MTC is exchanging parts.”
“MTC 处于交换组件状态。”
Q513601 “May I abandon MTC parts?”
“是否废弃 MTC 组件？”
I513801 “There are parts on the shuttle.|Please detach parts.”
“滑梭上有组件。|请取下组件。”
I513802 “It is temporary stop by the part protection.|Please detach parts.”
“因保护组件暂停。|请取下组件。”
I513803 “BGA parts cannot be returned.|Please detach parts.”
“不能归还 BGA 组件。|请取下组件。”
E514001 “MTS abnormal operation was generated.”
“MTS 运转异常。”
E514002 “Parts that MTS is different were drawn out.”
“MTS 抽出异样组件。”
W514401 “The power supply of MTC is turning off.”
“MTS 电源被关闭。”
W514402 “MTS is an emergency stop.”
“MTS 被紧急停止。”
W514403 “MTS is an initialize.”
“MTS 未结束原点返回。”
W514404 “MTS is off-line.”
“MTS 处于关闭状态。”
W514405 “MTS is a door opening.”
“MTS 机箱门被打开。”
W514406 “MTS is no stacker.”
“MTS 无堆栈箱。”
W514407 “MTS is making an error.”
“MTS 处于出错状态。”
W514408 “MTS is exchanging parts.”
“MTS 处于交换组件状态。”
Q514601”May I abandon MTS parts?”
“是否废弃 MTS 组件？”
I514802 “It is temporary stop by the part protection.|Please detach parts.”
“为保护组件暂停。|请取下组件。”
E515001 “DTS abnormal operation was generated.”
“DTS 运转异常。”
E515002 “Parts that DTS is different were drawn out.”
“DTS 抽出不同组件。”
W515401”DTS is an initialize.”
“DTS 未结束原点返回。”
W515402”DTS is a cover opening.”
“DTS 机盖被打开。”
W515403”DTS is making an error.”
“DTS 处于出错状态。”
W515404”DTS is exchanging parts.”
“DTS 处于交换组件状态。”
E520000 “Pick Miss Occured from MTC shuttle”
“不能吸取 MTC 上的组件。”
E520001 “The componet On MTC shuttle is different with Requested one”
“MTC 上的组件与指定组件不一致。”
E520002 “MTC Error Occured when doing Componet return to MTC”
“给 MTC 归还组件时，MTC 发生错误。”
E520003 “MTC shuttle Vacuum Error Occured when doing Componet return to MTC”
“给 MTC 滑梭归还组件时，滑梭真空出错。”
E520012 “When a component was returned to MTC shuttle,| the error of bringing a component to the head
occurred.”
“给 MTC 滑梭归还组件时，|发生 Head 附着组件返回的错误。”
E521005 “Laser Error:(LNK_FAIL) | A data error occurred on the communication link from the sensor to the
MCM.”
“激光错误:(LNK_FAIL) |传感器与 MCM 之间通讯发生错误。”
E521007 “Laser Error:(NO_ALG) | The NO_ALG action was requested.”
“激光错误:(NO_ALG) |被要求错误测量方法。”
E521008 “Laser Error:(NO_START) | Eiter the sensor is not connected or there is a hardware error.”
“激光错误:(NO_START) |没有连接传感器，或硬件出错。”
E521010 “Laser Error:(BAD_SENSOR) | The MCM was unable to detect valid sensor data.”
“激光错误:(BAD_SENSOR) |MCM 不能检索正确的传感器数据。”
E521012 “Laser Error:(BAD_EE_VERSION) | The firmware does not recongize the sensor EEPROM
version.”
“激光错误:(BAD_EE_VERSION) |固件不能识别 EEPROM 版本。”
E521013 “Laser Error:(BAD_EE_DATA) | There is an error reading calibration data from the sensor
EEPROM.”
“激光错误:(BAD_EE_DATA) |从传感器 EEPROM 读取校准数据发生错误。”
E521014 “Laser Error:(BAD_EE_SYNC) | There is an error reading calibration data from the sensor
EEPROM.”
“激光错误:(BAD_EE_SYNC) |从传感器 EEPROM 读取校准数据发生错误。”
E521015 “Laser Error:(POWER_LOW) | The MCM detected that the incoming voltage level was below that
required for proper sensor opration.”
“激光错误:(POWER_LOW) |MCM 发现电压下降，导致传感器不能正常运作。”
E521017 “Laser Error:(OVER_CURR) | The MCM detect that power to the sensor was low.”
“激光错误:(OVER_CURR) |MCM 发现电压下降，导致传感器不能正常运作。”
E521060 “Laser Error:(SHORT_BUF) | The communication buffer contained fewer bytes than specified by
the length.”
“激光错误:(SHORT_BUF) |激光数据用通讯缓冲区字节长度偏小。”
E521061 “Laser Error:(LONG_BUF) | The communication buffer contained more bytes than spcified by the
length.”
“激光错误:(LONG_BUF) |激光数据用通讯缓冲区字节长度偏小。”
E521062 “Laser Error:(SHORT_CMD) | The length specified is smaller than expected by the command.”
“激光错误:(SHORT_CMD) |激光命令用通讯缓冲区字节长度偏小。”
E521063 “Laser Error:(LONG_CMD) | The length specified is smaller than expected by the command.”
“激光错误:(LONG_CMD) |激光命令用通讯缓冲区字节长度偏小。”
E521083 “Laser Error:(BAD_CHKSUM) | The firmware found an error while reading the sensor EEPROM.”
“激光错误:(BAD_CHKSUM) |固件从传感器 EEPROM 读取数据中发现错误。”