JUKI贴片机错误代码集合.pdf - 第54页
width and the board size in Y direct ion. [Treatment] Please adjust the difference be tween t he conveyor width and the board size in Y dir ection wi th a hand knob, then try again. E291011 “ Cannot move conveyor ” “ 不能移…
Please check and see if the conveyor works properly with Manual control.
E291005 “The axis cannot be moved. | Execution is aborted”
“轴不能移动。|停止运行。”
[Cause]
The axis could not move for some reason.
[Treatment]
Please check and see if the axis works properly with Manual control.
E291006 “The BOC mark data is not set. | Operation is aborted”
“没有设置 BOC 标记数据。|停止运行。”
[Cause]
BOC mark was not set in the Board data or the Board data is incomplete.
[Treatment]
Please set and complete the board data.
E291007 “The OCC device is set in unused by the setup”
“在设置中，OCC 装置没有被选用。”
[Cause]
The OCC device is set to “not use” in Setup.
[Treatment]
If the device is available, set it to “use” in Setup. If not, this operation cannot be executed.
E291008 “Value is mistake”
“设置数据有差错。”
[Cause]
The value is wrong when you hit the Enter key to define it.
[Treatment]
Please check the entered value.
E291009 “Value out of range”
“设置数据超出范围。”
[Cause]
The value when you hit the Enter key to define it exceeded the input range.
[Treatment]
Please enter a value which is within the input range.
E291010 “Conveyor margin out of range. It is not possible to operation”
“因传送边界超出范围，不能进行操作。”
[Cause]
Failed to take the value in as a margin since there is a too much difference between the conveyor
width and the board size in Y direction.
[Treatment]
Please adjust the difference between the conveyor width and the board size in Y direction with a hand
knob, then try again.
E291011 “Cannot move conveyor”
“不能移动传送幅宽。”
[Cause]
This error occurs when the conveyor width cannot be adjusted for some reason. There is a possibility
that an obstruction is being detected by a sensor on the conveyor.
[Treatment]
Please make sure that there is no obstruction to be detected by sensors between the current position
and the destination.
E291012 “The BOC mark recognition error [Circuit : %d / %d point]”
“识别 BOC 标记发生错误 [ 电路号 : %d / %d 点 ]”
[Cause]
VCS could not recognize the BOC mark(s).
1): Circuit number
2): The Xth BOC mark.
[Treatment]
There is a possibility that the BOC mark(s) could not be taught to the machine properly.
E291013 “The area sensor was detected. Execution is aborted”
“发现位置错误。结束运行。”
[Cause]
The process got forcibly aborted since the area sensor detected something.
[Treatment]
Please remove the factor that was detected by the sensor.
E291014 “Emergency stopped. Execution is aborted”
“紧急停止状态。结束运行。”
[Cause]
The process got forcibly aborted since the Emergency STOP occurred.
[Treatment.]
Please remove the cause of the Emergency STOP.
E291015 “PWB exist in the entry side center buffer. | Please execute retry after ejection”
“入口缓冲处存在基板。|搬出入口处基板后，再次执行。”
[Cause]
PWB loading did not succeed since a PWB is staying on the inlet side of the buffer.
[Treatment]
Please take the PWB off the inlet side of the buffer.
E291016 “PWB exist in the exit side center buffer. | Please execute retry after ejection”
“出口缓冲处存在基板。|搬出出口处基板后，再次执行。”
[Cause]
PWB loading did not succeed since a PWB is staying on the outlet side of the buffer.
[Treatment]
Please take the PWB off the outlet side of the buffer.
E291017 “There is no completed pickup data”
“不存在已经完成的吸取数据。”
[Cause]
The process could not be executed since there is no complete data.
[Treatment]
Please input and complete the pickup data.
E291018 “Input string is mistake”
“字符串错误。”
[Cause]
Character(s) was wrong when you hit the Enter key to define the caricature(s).
[Treatment]
Please re-enter characters.
E291019 “Range is mistake”
“范围错误。”
[Cause]
The value exceeded the input range when you hit the Enter key to define the value.
[Treatment]
Please enter a value which is within the input value.
E291020 “Please check the feeder to trace”
“请检查要跟踪的送料器。”
[Cause]
No feeders to trace are selected.
[Treatment]
Please select a feeder to trace.
E291021 “There is no completed placement data”
“不存在已经完成的贴片数据。”
[Cause]