JUKI贴片机错误代码集合.pdf - 第197页
[Treatment] Please turn off the power supply of your machine and reboot it. E610016 “ An error occurred when start ing Theta axis revolution ” “ θ轴移动开始时发生错误。 ” [Cause] An error occurred when starting Theta axis (nozzle r…
The specifying of ATC position is abnormal. The data in the machine is broken or the version of the
software that is installed on the machine is not correct.
[Treatment]
‧Please turn off the power supply of your machine and reboot it.
‧If the error occurred after the installation or the version up of the software, you need to re-install
the software.
‧If the treatments above do not work, there is a possibility that MPX board(s) in the machine is
broken. You need to replace it(them) with new ones.
E610011 “An error occurred when starting XY axes movement”
“XY 轴移动开始时发生错误。”
[Cause]
An error occurred when starting XY axes movement.
[Treatment]
Please turn off the power supply of your machine and reboot it.
E610012 “An error occurred when starting X axis movement”
“X 轴移动开始时发生错误。”
[Cause]
An error occurred when starting X axis (left side) movement.
[Treatment]
Please turn off the power supply of your machine and reboot it.
E610013 “An error occurred when starting XR axis movement”
“XR 轴移动开始时发生错误。”
[Cause]
An error occurred when starting X axis (right side) movement.
[Treatment]
Please turn off the power supply of your machine and reboot it.
E610014 “An error occurred when starting Y axis movement”
“Y 轴移动开始时发生错误。”
[Cause]
An error occurred when starting Y axis movement.
[Treatment]
Please turn off the power supply of your machine and reboot it.
E610015 “An error occurred when starting Z axis movement”
“Z 轴移动开始时发生错误。”
[Cause]
An error occurred when starting X axis (nozzle up-and-down axis) movement.
[Treatment]
Please turn off the power supply of your machine and reboot it.
E610016 “An error occurred when starting Theta axis revolution”
“θ轴移动开始时发生错误。”
[Cause]
An error occurred when starting Theta axis (nozzle revolving axis) revolution.
[Treatment]
Please turn off the power supply of your machine and reboot it.
E610017 “An error occurred while XY axes are traveling”
“XY 轴移动时发生错误。”
[Cause]
An error occurred while XY axes are traveling.
[Treatment]
Please turn off the power supply of your machine and reboot it.
E610018 “An error occurred while X axis is traveling”
“X 轴移动时发生错误。”
[Cause]
An error occurred while X axis (left side) is traveling.
[Treatment]
Please turn off the power supply of your machine and reboot it.
E610019 “An error occurred while XR axis is traveling”
“XR 轴移动时发生错误。”
[Cause]
An error occurred while X axis (right side) is traveling.
[Treatment]
Please turn off the power supply of your machine and reboot it.
E610020 “An error occurred while Y axis is traveling”
“Y 轴移动时发生错误。”
[Cause]
An error occurred while Y axis is traveling.
[Treatment]
Please turn off the power supply of your machine and reboot it.
E610021 “An error occurred while Z axis is traveling”
“Z 轴移动时发生错误。”
[Cause]
An error occurred while Z axis (Nozzle up-and-down axis) is traveling.
[Treatment]
Please turn off the power supply of your machine and reboot it.
E610022 “An error occurred while Theta axis is revolving”
“θ轴移动时发生错误。”
[Cause]
An error occurred while Theta axis (Nozzle revolving axis) is traveling.
[Treatment]
Please turn off the power supply of your machine and reboot it.
E610023 “No nozzle has been assigned to the cylinder”
“圆筒上没有分配吸嘴。”
[Cause]
No nozzle has been assigned to the specified ATC.
[Treatment]
Please set nozzle(s) on ATC and perform the ATC nozzle allocation. The ATC Nozzle allocation can
be performed by selecting [Machine Setup] from the menu bar, and then [Setting Group(G)] [ATC
Nozzle Allocation(A)].
E610024 “Nozzle installation was tried with a head which already has a nozzle”
“吸嘴已被安装，可又执行安装吸嘴。”
[Cause]
Nozzle installation was tried with a head which already has a nozzle. A cause is either that a nozzle is
actually on the head or that the window of the laser sensor is dirty.
[Treatment]
If a nozzle is installed on the head.
The nozzle is likely to have been set on the head manually. Please take it off by hand.
If a nozzle is NOT installed on the head.
‧Please clean the window of the laser sensor. You can check the dirt of the window with the
following procedures. Select [Manual Control] from the menu bar, and then select [Control(C)]
[Head(H)] [Laser Control(L)]. Select a concerned laser sensor in 'Control' unit, and then select 'Image
displaying' from 'Control Item' frame. By enabling ON, an image data will be shown.
‧If the treatment1 does not work, or if the image data does not appear, there is a possibility that the
MCM board in the laser sensor is not installed properly or the sensor itself is broken. Please turn off
the power supply and see if the MCM board is installed in the sensor correctly.
E610025 “Nozzle returning was requested to a head which does not have any nozzles”
“吸嘴不存在，可执行放回吸嘴。”
[Cause]