JUKI贴片机错误代码集合.pdf - 第118页
“ 在设置数据中，传送带浮动选项为 无效状态， | 不间断运行被选用。 ” W503600 “ The input data is over the Input range(%s).|Would you like to s et the data? ” “ 输入的数据超过输入范围， | 是否继续 设置？ ” W503601 “ The input data is changed.|Is the data setti ng ended? …
“前一次结束生产时的生产站台(%s)和这一次指定的生产站台(%s)不同，|将丢失一侧站台的
继续生产情报，是否继续生产？ “
W503404 “The production execution station (%s) specified the production execution station (%s) of the last
time end at this time is different.|Is production started though the continuance production cannot be
done at this time?”
“前一次结束生产时的生产站台(%s)和这一次指定的生产站台(%s)不同，|这次不能进行继
续生产，是否开始生产？”
W503405 “The production mode (%s) set at this time as the production mode (%s) when ending last time is
different according to using unused of the unit.|Is production started though the continuance
production cannot be done at this time?”
“前一次结束生产时的生产模式(%s)和这一次生产模式(%s)，因单元的使用情况不同而不
同。|这次不能进行继续生产，是否开始生产？”
W503406 “The sequence(%s) you selected is different from the one(%s) of when the production got suspended
last time.|Is production started though the continuance production cannot be done at this time?”
“前一次结束生产时的顺序(%s)和这一次选择的顺序(%s)不一样。|这次不能进行继续生产，
是否开始生产？”
W503407 “The prod. start end position where it is set to end last time at the prod. start end pos. and this time
is different.|Is production started though the continuance production cannot be done at this time?”
“前一次结束生产时的生产开始和结束位置与这一次设置的生产开始和结束位置不同，|这
次不能进行继续生产，是否开始生产？”
W503408 “Differing the Place station of the last time end and the Place station of this time exists.|Is
production started though the continuance production cannot be done at this time?”
“前一次结束生产时的贴片站台与这一次贴片站台不同。|这次不能进行继续生产，是否开
始生产？”
E503500 “No completion change plan. Please use Feeder Bank”
“未完成替换准备，|请使用送料器台架。”
[Cause]
This message appears if Non-stop production is set in the Operation Option and the feeder bank on
the front side is descending down when reading a file in.
[Treatment]
Please have the feeder bank ascend.
W503501 “There is no trolley option in the setup data.|The non-stop operation is selected.”
“在设置数据中，交换台选项为无效状态，|不间断运行被选用。”
W503502 “There is no feeder float sensor in the setup data.|The non-stop operation is selected.”
“在设置数据中，传送带浮动选项为无效状态，|不间断运行被选用。”
W503600 “The input data is over the Input range(%s).|Would you like to set the data?”
“输入的数据超过输入范围，|是否继续设置？”
W503601 “The input data is changed.|Is the data setting ended?”
“数据正在被更新，|是否结束数据更新？”
W503700 “There is no Data.|Please select the area where the data is displayed.”
“没有数据，|请选择数据。”
W503800 “The head is specified for an unused head by the place data.|The input order production cannot be
executed.”
“在贴片数据上，指定了不使用 Head，|不能进行输入顺生产。”
W503801 “Right or Left OCC is unused.|(There is both head specification in the production program.)|The
input order production cannot be executed.”
“不使用或左或右 OCC|(生产程序内已经指定两个 Head)，|不能进行输入顺生产。”
W503802 “Left OCC is unused.|(There is left head specification in the production program.)|The input order
production cannot be executed.”
“不使用左 OCC|(生产程序内已经指定左 Head)，|不能进行输入顺生产。”
W503803 “Right OCC is unused.|(There is right head specification in the production program.)|The input order
production cannot be executed.”
“不使用左 OCC|(生产程序内已经指定左 Head)，|不能进行输入顺生产。”
W503804 “There is a station which it is a setup and is unused.|(There is both head specification in the
production program.)|The input order production cannot be executed.”
“在设置中存在不使用站台|(生产程序内已经指定两个 Head)，|不能进行输入顺生产。”
W503805 “It is a setup and a left station is unused.|(There is left head specification in the production
program.)|The input order production cannot be executed.”
“在设置中，左站台处于不使用状态|(生产程序内已经指定左 Head)，|不能进行输入顺生产。”
W503806 “It is a setup and a right station is unused.|(There is right head specification in the production
program.)|The input order production cannot be executed.”
“在设置中，右站台处于不使用状态|(生产程序内已经指定右 Head)，|不能进行输入顺生产。”
W503810 “It is the data which the exit side station installs earlier than the entrance side station.|The input
order production cannot be executed.”
“存在出口侧站台比入口侧站台先进行贴片的数据，|不能进行输入顺生产。”
W503820 “There is no adjustment in setting the pick position and the use unit.|The input order production
cannot be executed.”
“吸取位置或使用单元的设置不整合，|不能进行输入顺生产。”
W503860 “Order production warning.|Resume the product cannot be executed.”
“这次生产条件与继续生产程序条件不同。|不能进行继续生产。”
W503900 “There is a possibility with which the laser of %s is dirty. Is production executed?”
“%s 的激光可能被弄脏，是否进行生产？”
W503910 “Nozzle is set on %s.|Remove the nozzle.|Nozzle moves to nozzle of wait position by selecting
'OK'.”
“%s 位置上吸嘴被安装，|请取出吸嘴，|选择确定键，移到模具位置。”
W504000 “The PWB on LEFT station can't re-clamp.”
“在左站台上，不能重新固定基板。”
W504001 “The PWB on RIGHT station can't re-clamp.”
“在右站台上，不能重新固定基板。”
W504002 “Remove the PWB on LEFT station.”
“请取下左站台上的基板。”
W504003 “Remove the PWB on RIGHT station.”
“请取下右站台上的基板。”
W504004 “The PWB on LEFT station don't exist.”
“左站台的传送轨道上无基板。”
W504005 “The PWB on RIGHT station don't exist.”
“右站台的传送轨道上无基板。”
W504006 “The PWB on BOTH station can't re-clamp.”
“在两个站台上，都不能重新固定基板。”
W504007 “Remove the PWB on BOTH station.”
“请取下两个站台上的基板。”
W504008 “The PWB on BOTH station don't exist.”
“两个站台的传送轨道上都没有基板。”
W504009 “The PWB on the station can't re-clamp.”
“不能重新固定基板。”
W504010 “Remove the PWB on the station.”
“请取下基板。”