JUKI贴片机错误代码集合.pdf - 第450页
E6105 Pl ease select component. " 请选择组件。 " [Cause] Appears if the number of supplie s change butt on is pressed with out a list selected. [Deal] Click the part name to highlight it and press the change butto n …
"显示对话框失败。"
E6007 System error has occurred.
"出现系统错误。"
[Cause]
After creating a table for mounting, creating a feeder layout window with no mounting data was
failed.
[Deal]
Consult the manufacturer.
E6008 Failed to combine the program.
[Cause]
Merging the divided programs was failed.
[Deal]
Retry the process.
E6009 Tact simulation failed.
[Cause]
An error was detected at the line entry. Insufficient free space in the memory or a failure on the disk
is suspected.
[Deal]
Run the "Scan-disk" to check the disk. Exit from other applications, and retry the process.
E6100 Number supplied is out of range.
"供给的数量超出范围。"
[Cause]
An excessive value was specified for the number of supplies.
[Deal]
Enter a value within the range.
E6101 “Error occurred in finding number supplied, upper limit of number supplied or lower limit of
number supplied. “
"在查找提供数量时出现错误，增加提供的数量限制或降低提供的数量限制。"
E6102 “HLC.INI file read-in failed. “
"读入 HLC.INI 文件失败。"
E6103 “Data is input so as to eliminate all machine stations from partition destinations. “
" 数据被输入为了从注定分开区域终止所有机器位置。"
E6104 “Number of distributed stations is outside limits. “
"分配位置数量超过外部限制。"
E6105 Please select component.
"请选择组件。"
[Cause]
Appears if the number of supplies change button is pressed without a list selected.
[Deal]
Click the part name to highlight it and press the change button or double-click the part name.
E6106 “HLCSETUP.INI file read-in failed. “
"读入 HLCSETUP.INI 文件失败。"
E6109 Enter numeric value.
[Cause]
Appears if no numeric value or any value other than numeric is specified for the feedback option and
the number of redundant factors.
[Deal]
Specify valid values for the feedback option or the number of redundant factors.
E6110 Setting of the number of max loop count is out of range.
[Cause]
An excessive number of the maximum loops was specified for the feedback option.
[Deal]
Enter a value within the range, 1 to 9.
E6111 Setting of target difference time is out of range.
[Cause]
Excessive value was specified for the allowable interval of the feedback option.
[Deal]
Enter a value within the range, 0 to 60 seconds.
E6112 Cannot distribute data with this setting.
[Cause]
For every station, 0 is specified in the balance option.
[Deal]
Check the station to allocate mounting points or application points, and specify the distribution.
E6113 Setting of balance is out of range.
[Cause]
An excessive value was specified for the balance option.
[Deal]
Enter a vale within the range, 0 to 100.
E6114 Setting of room coefficient is out of range.
[Cause]
An excessive value was specified for the redundant factor.
[Deal]
Enter a value within the range, 0 to 100.
E6250 “Area cannot be secured. “
"区域不能被保护。"
E6251 “INI file cannot be read. “
"不能读 INI 文件。"
E6252 “Distributed data cannot be read. “
"不能读分配数据。"
E6253 “Data combining failed. “
"数据结合失败。"
E6254 “Combining of data failed because data are mutually exclusive. “
"由于数据相互排斥数据结合失败。"
E6255 “Combined data cannot be output. “
"不能输出组合数据。"
E6300 “Setting of number of programs etc. failed. “
"设置程序数量等失败。"
E6350 Area cannot be secured.
"区域不能被保护。"
[Cause]
Allocating the memory for EPU was failed. Allocating the memory for G3h and G3N was failed.
[Deal]
Exit from other applications and retry the process.
E6351 File read failed.
"不能读预定程序目录。"
[Cause]
Loading files, G3H and GXL, was failed. Insufficient free space on the memory or any failure on the
disk is suspected.
[Deal]
Run the "Scan-disk" to check the disk. Exit from other applica
tions and retry installation.