JUKI贴片机错误代码集合.pdf - 第15页
Please turn on the power supply of t he machine after finishing everything and shutting down the machine. If the error occurs even after the reboot ing, there is a possib ility that somethi ng is wrong with the a x i s .…
“连接安全驱动器失败。”
E109002 “Failed to interface with the Laser drivers.”
“连接激光驱动器失败。”
E109003 “Failed to interface with the Conveyor drivers.”
“连接搬运驱动器失败。”
E109004 “Failed to interface with the AWC drivers.”
“连接自动调整基板宽度驱动器失败。”
E109005 “Failed to interface with the MTC/MTS/DTS drivers.”
“连接 MTC/MTS/DTS 驱动器失败。”
E109110 “Fatal error occurred in constructing axes structure. | Abort the process”
“建立轴处理构造失败。|请关闭程序，重新启动。”
[Cause]
An error occurred in the process of creating axis structure that meets the machine hardware.
[Treatment]
Please turn on the power supply of the machine after finishing everything and shutting down the
machine.
If the error occurs even after the rebooting, there is a possibility that a system file is broken.
Please take a note of the error number and contact our technical service dept. for information.
E109120 “Fatal error occurred in initializing axes. | Abort the process”
“轴初始化失败。|请关闭程序，重新启动。”
[Cause]
An error occurred while starting the Axis Control process.
[Treatment]
Please turn on the power supply of the machine after finishing everything and shutting down the
machine.
If the error occurs even after the rebooting, there is a possibility that a system file is broken or that
something is wrong with XMP board or other connectors. .
Please take a note of the error number and contact our technical service dept. for information.
E109130 “Failed to originate, Please retry”
“返回原点失败，请再次执行。”
[Cause]
An error occurred during the Home returning process.
1): Detailed code
2): An error of the axis process
[Treatment]
Please turn on the power supply of the machine after finishing everything and shutting down the
machine.
If the error occurs even after the rebooting, there is a possibility that something is wrong with the
axis.
Please take a note of the error number and contact our technical service dept. for information.
E109131 “Failed to originate, because of Z-Axis Failure.|Please retry.”
“因 Z 轴下降发生错误，返回原点失败。|请再次执行。”
E109132 “Failed to originate, because of Feeder-Floating.|Please retry.”
“因传送带浮动，返回原点失败。|请再次执行。”
E109133 “Failed to originate, because of Servo On Failure.|Please retry.”
“因启动伺服发生错误，返回原点失败。|请再次执行。”
E109134 “Failed to detect the home of Theta-axis.|Please retry origination.”
“因θ轴查出原点发生错误，返回原点失败。|请再次执行。”
E109135 “Failed to detect the home of Z-axis.|Please retry origination.”
“因 Z 轴查出原点发生错误，返回原点失败。|请再次执行。”
E109136 “Failed to recognize the mark of XL.|Please retry origination.”
“因识别标记(XL)发生错误，返回原点失败。|请再次执行。”
E109137 “Failed to recognize the mark of XR.|Please retry origination.”
“因识别标记(XR)发生错误，返回原点失败。|请再次执行。”
E109138 “Failed to detect the home of the Back Up Table.|Please retry origination.”
“因支撑台查出原点发生错误，返回原点失败。|请再次执行。”
E109140 “Failed to detect the home of the AWC.”
“调整基板幅宽的返回原点失败。”
E109141 “AWC failure was detected.”
“发现调整基板幅宽的驱动错误。”
E109210 “Failed to initialize DTS”
“DTS 返回原点失败。”
[Cause]
An error occurred during the Home returning of DTS.
[Treatment]
Please turn on the power supply of the machine after finishing everything and shutting down the
machine.
If the error occurs even after the rebooting, there is a possibility of DTS failure, Air pressure failure,
or Feeder knock-pin failure.
Please take a note of the error number and contact our technical service dept. for information.
E109220 “Error was detected in checking if any nozzles attached”
“检查吸嘴安装发生错误。”
[Cause]
An error occurred while checking the nozzle installation.
[Treatment]
Please turn on the power supply of the machine after finishing everything and shutting down the
machine.
If the error occurs even after the rebooting, there is a possibility of the laser failure or the axis failure.
Please take a note of the error number and contact our technical service dept. for information.
W109221 “There are some attached nozzles”
“吸嘴被安装在上面。|请手动取下吸嘴。”
[Cause]
a nozzle which the machine does not recognize is installed.
[Treatment]
Please return the nozzle to ATC manually.
If such a nozzle has not been installed on the head, there is a possibility that the laser is too dirty to
work properly or that the laser is broken. If so, please clean the laser.
If such a nozzle still seems to be installed when you perform the Nozzle laser measurement by
Manual control, please take a note of the error number and contact our technical service dept. for
information.
W109230 “Each I/O is moving to the own safe position, OK?”
“进行 I/O 安全方向设置。”
[Cause]
You are informed that actions such as nozzle returning or I/O reset will begin.
[Treatment]
As long as you do not see any obstructions against the action, please execute it.
E109231 “Please remove the PWB's, and initialize the axes.”
“请取下基板后，再次执行回原点。”
E109300 “Returning to home has not yet been completed.”
“返回原点尚未结束。”
E109301 “Servo is in the free state.”
“伺服处于未使用状态。”