JUKI贴片机错误代码集合.pdf - 第120页
W504011 “ The PWB on the station don't exist .” “ 传送轨 道上没有基板。 ” W504012 “ When sequential mode or mixed m ode,the PWB on %s can't re-clamp .” “ 次序混 合模式生产时，不能运行 %s 的重新固定基板。 ” W504020 “ When left station is speci…
cannot be executed.”
“吸取位置或使用单元的设置不整合，|不能进行输入顺生产。”
W503860 “Order production warning.|Resume the product cannot be executed.”
“这次生产条件与继续生产程序条件不同。|不能进行继续生产。”
W503900 “There is a possibility with which the laser of %s is dirty. Is production executed?”
“%s 的激光可能被弄脏，是否进行生产？”
W503910 “Nozzle is set on %s.|Remove the nozzle.|Nozzle moves to nozzle of wait position by selecting
'OK'.”
“%s 位置上吸嘴被安装，|请取出吸嘴，|选择确定键，移到模具位置。”
W504000 “The PWB on LEFT station can't re-clamp.”
“在左站台上，不能重新固定基板。”
W504001 “The PWB on RIGHT station can't re-clamp.”
“在右站台上，不能重新固定基板。”
W504002 “Remove the PWB on LEFT station.”
“请取下左站台上的基板。”
W504003 “Remove the PWB on RIGHT station.”
“请取下右站台上的基板。”
W504004 “The PWB on LEFT station don't exist.”
“左站台的传送轨道上无基板。”
W504005 “The PWB on RIGHT station don't exist.”
“右站台的传送轨道上无基板。”
W504006 “The PWB on BOTH station can't re-clamp.”
“在两个站台上，都不能重新固定基板。”
W504007 “Remove the PWB on BOTH station.”
“请取下两个站台上的基板。”
W504008 “The PWB on BOTH station don't exist.”
“两个站台的传送轨道上都没有基板。”
W504009 “The PWB on the station can't re-clamp.”
“不能重新固定基板。”
W504010 “Remove the PWB on the station.”
“请取下基板。”
W504011 “The PWB on the station don't exist.”
“传送轨道上没有基板。”
W504012 “When sequential mode or mixed mode,the PWB on %s can't re-clamp.”
“次序混合模式生产时，不能运行%s 的重新固定基板。”
W504020 “When left station is specified,the PWB on RIGHT station can't re-clamp.”
“指定左站台时，如果右站台上存在基板，就不能重新固定。”
W504021 “When left station is specified,the PWB on LEFT station can't re-clamp.”
“指定右站台时，如果左站台上存在基板，就不能重新固定。”
W507603 “You can use this program for measuring general placement offset.”
“贴片综合偏差生产用生产程序。”
Q506001 “The measurement of the height of component of the %s failed.|Do you measure again?”
“测量%s 送料器组件高度失败，|是否再试？”
Q506002 “Stop Key is pressed in the measurement of the height of component of the %s.|Do you want to exit
measurement?”
“测量%s 送料器组件高度，被停止按钮而停止，|是否停止测量？”
Q506011 “Verification inspection of component of the %s failed.| Specified value| %s|
Measurement value| %s| Inspection result| %s|Do you inspect again?”
“测量%s 送料器组件的数值检查失败。| 指定值: %s | 测定值：%s | 检查结果: %s | 是否再
检查？ “。
Q506012 “Stop Key is pressed in verification inspection of component of the %s.|Do you want to exit
inspection?”
“测量%s 送料器数值检查中停止健被按下，|是否结束检查？ “
Q506021 “SOT direction inspection of component of the %s failed.|Do you inspect again?”
“%s 送料器组件 SOT 方向检查失败，|是否再试？”
Q506022 “Stop Key is pressed in SOT direction inspection of component of the %s.|Do you want to exit
inspection?”
“%s 送料器组件 SOT 方向检查，被停止按钮而停止，|是否停止检查？”
E506100 “You can resume the production from the last suspended position |%s |%s | Would you like to
resume the production?”
[Cause]
This message appears if the production is resumable when reading a file in.
|Resumptive production starting position of each station.
[Treatment]
Yes: Starts the production from the placement point which got illegal abortion last time.
No: Will not resume the production but start a normal production that is set in the Production
Condition.
E506101 “You need to delete the file if you do not resume the production from the last illegally suspended
position. |%s|%s| Would you like to delete the file?”
“在生产基板中，如果不想执行前一次异常退出时|%s|%s|的继续生产，就必要删除它，|是
否删除？”
[Cause]
This message appears if you select 'do not resume the production' when you are asked if to resume the
production when reading a file in or the Production screen got started.
[Treatment]
Yes : Deletes the resumable production file. If you delete the file, you can no longer resume the
production from the point where the production got illegal abortion.
No : Will not delete the resumable production file.
E506102 “Would you like to resume the production? The last suspended position |%s|%s|”
[Cause]
This message appears if the production program is a resumable production when starting a
production.
(For 2030)
|Resumptive production starting position of each station.
[Treatment]
Yes: Starts the production from the placement point which got illegal abortion last time.
No: will not resume the production but start a normal production that is set in the Production
Condition.
E506200 “You can resume the production from the last suspended position | [Circuit No. : %d Step No. : %d]
Would you like to resume the production?”
[Cause]
This message appears if the production program is a resumable production when starting a
production.
(For 2030)
|Resumptive production starting position of each station.
[Treatment]
Yes : Starts the production from the placement point which got illegal abortion last time.
No : Will not resume the production but start a normal production that is set in the Production
Condition.