JUKI贴片机错误代码集合.pdf - 第453页
Complete the mounting data. E6404 Component data is not completed. " 组件数据不完全。 " [Cause] The part data where the mounti ng position is allocated is incom plete. [Deal] Complet e the part data. E6405 Pick data ar…
E6352 “Data before distribution cannot be read. “
"不能读分配前的数据。"
E6353 “Distribution option cannot be read. “
"不能读分配选项。"
E6354 Reference table cannot be read.
"不能读资料表。"
[Cause]
Loading files, OPTIM.INI and CYCLE.INI. It is suspected that the installation was failed or any
failure occurred on the disk.
[Deal]
Run the "Scan-disk" to check the disk. Exit from other applications and retry installation.
E6355 “Station information cannot be read. “
"不能读位置信息。"
E6356 Resource data cannot be read.
"不能读资源数据。"
[Cause]
Loading a files HLCSETUP.INI. It is suspected that the installation was failed or any failure occurred
on the disk.
[Deal]
Run the "Scan-disk" to check the disk. Exit from other applications and retry installation.
E6357 “Permanent data cannot be read. “
"不能读永久数据。"
E6358 “Station order conflicts with the optimization that was excuted. “
"优化的位置顺序有冲突."
E6400 “Component in program and permanent component are improperly positioned. “
"在程序中的组件和永久性组件位置不正确."
E6402 “PWB data is not completed. “
"基板数据不完全。"
E6403 Component data are incomplete. (No.%d)
"贴片数据不完全。"
[Cause]
The mounting data is incomplete.
[Deal]
Complete the mounting data.
E6404 Component data is not completed.
"组件数据不完全。"
[Cause]
The part data where the mounting position is allocated is incomplete.
[Deal]
Complete the part data.
E6405 Pick data are incomplete.
"吸取数据不完全。"
[Cause]
The pick data is incomplete.
[Deal]
Complete the pick data.
E6406 “Vision data is not completed. “
"图像数据不完全。"
E6407 “Specified number supplied exceeds resource. “
"提供的特殊数字超过资源数。"
E6408 “Assigned placement data exist in plural number of stations. “
"指定贴片数据存在于复数位置。"
E6409 “Assigned pick data exist in multiple stations. “
"指定挑选数据存在于多个位置。"
E6420 “Component in %dth program is overlapped with permanent component. “
"在%dth 程序中的组件被永久组件覆盖 "
E6422 “PWB data in %dth program is not completed. “
"在％dth 程序的基板 B 数据不完全。"
E6423 “Placement data in %dth program is not completed. “
"在％dth 程序的贴片数据不完全。"
E6424
“Component data in %dth program is not completed. “
"在％dth 程序的组件数据不完全。"
E6425 “Pick data in %dth program is not completed. “
"在%dth 程序中的吸取数据不完全。"
E6426 “Vision data in %dth program is not completed. “
"在%dth 程序中的图像数据不完全。"
E6427 “Specified number supplied in %dth program exceeds resource. “
"在 %dth程序供给指定数量超过资源数。"
E6428 “Assigned placement data in %dth program exist in multiple stations. “
"在%dth 程序中的指定贴片数据存在于多个位置。"
E6429 “Assigned pick data in %dth program exist in multiple stations. “
"在%dth 程序中的指定挑选数据存在于多个位置。"
E6440 The number of placemently resident nozzles exceeds the resource.
"固定吸嘴数量超过资源量。"
[Cause]
The number of the placement nozzles has exceeded the available number of resources.
[Deal]
Increase the number of nozzles specified in the MSL setup resource.
E6441 “Number of permanent feeders exceeds resource. “
"固定进料器数量超过资源量。"
E6442 %s over resource.
[Cause]
The number of feeders has exceeded the available number of resources.
[Deal]
Increase the number of feeders specified in the MSL setup resource.
E6450 “Permanent data cannot be set. “
"永久数据不能被设置。"
E6451 “Protected data cannot be set. “
"保护数据不能被设置。"
E6452 “
Production control data allocation failed. “
"产品控制数据分配失败。"
E6453 “Production condition data allocation failed. “
"产品情况数据分配失败。"
E6454 “Global fiducial data allocation failed. “
"球型基准数据分配失败。"
E6455 “Permanently resident nozzle allocation failed. “