JUKI贴片机错误代码集合.pdf - 第161页
E600036 “ Axis Driver:| The velocity erro r exceeded the limit.|(Check the power supply for the possibi lities of low power supply voltage.) ” “ 速度误差超过界限。 |( 可能电压不足， 请检查电压。 ) ” E600040 “ Axi s Driver:| Coordinates exceed…
[解决]
解决原因后，重新执行原点返回。
E600014 “Axis Driver:| Driver Alarm.”
“驱动警报。”
[原因]
伺服驱动器发生警报。
编码器线路接触不好或断线或障碍物的原因引起超负荷等因素值得考虑。
或者，按一下<紧急停止>开关也会发出警报。
[解决]
解决原因后，重新执行原点返回。
E600015 “Axis Driver:| Amp disabled.”
“伺服 Amp 失效。”
E600016 “Axis Driver:| Position of Z axis is low.”
“因 Z 轴下降，不能运转。”
E600017 “Axis Driver:| Feeder float detected.”
“因传送带浮动，不能运转。”
E600018 “Axis Driver:| Machine detected PWB interference with the check cylinder.”
“因基板检查传感器没有反应，不能运转。”
E600020 “Axis Driver:| Failed set gain.”
“设置增值参数失败。”
E600021 “Axis Driver:| Failed set LA encoder.”
“设置激光译码器失败。”
E600024 “Axis Driver:| Synqnet Interface Check error.”
“连接 Synqnet 失败。 “
E600030 “Axis Driver:| XMP error.”
“XMP 错误。”
E600031 “Axis Driver:| Status error.”
“轴状态错误。”
E600032 “Axis Driver:| Motion start error.”
“启动运行轴失败。”
E600033 “Axis Driver:| Motion stop error.”
“停止运行轴失败。”
E600036 “Axis Driver:| The velocity error exceeded the limit.|(Check the power supply for the possibilities of
low power supply voltage.)”
“速度误差超过界限。|(可能电压不足，请检查电压。)”
E600040 “Axis Driver:| Coordinates exceed a movable range.”
“超出正常移动范围。”
E600042 “Axis Driver:| Cannot continue operation because of cover open.”
“因为安全盖被打开,所以不能运行。”
E601001 “Axis Driver:| Failed servo power on.”
“伺服电源的打开失败。”
E601010 “Axis Driver:| Failed amp enable.(XY)”
“启动伺服驱动器失败。(XY)”
E601011 “Axis Driver:| Failed amp enable.(YC)”
“启动伺服驱动器失败。(YC)”
E601012 “Axis Driver:| Failed amp enable.(ZT1)”
“启动伺服驱动器失败。(ZT1)”
E601013 “Axis Driver:| Failed amp enable.(ZT2)”
“启动伺服驱动器失败。(ZT2)”
E601014 “Axis Driver:| Failed amp enable.(ZT3)”
“启动伺服驱动器失败。(ZT3)
E601015 “Axis Driver:| Failed amp enable.(ZT4)”
“启动伺服驱动器失败。(ZT4)”
E601020 “Axis Driver:| Failed amp disable.(XY)”
“中断 AMP 失败。(XY)”
E601021 “Axis Driver:| Failed amp disable.(Yc)”
“中断 AMP 失败。(Yc)”
E601022 “Axis Driver:| Failed amp disable.(ZT1)”
“中断 AMP 失败。(ZT1)”
E601023 “Axis Driver:| Failed amp disable.(ZT2)”
“中断 AMP 失败。(ZT2)”
E601024 “Axis Driver:| Failed amp disable.(ZT3)”
“中断 AMP 失败。(ZT3)”
E601025 “Axis Driver:| Failed amp disable.(ZT4)”
“中断 AMP 失败。(ZT4)”
E601030 “Axis Driver:| Failed alarm clear.(XY)”
“排除警报失败。(XY)”
E601031 “Axis Driver:| Failed alarm clear.(Yc)”
排除警报失败。(Yc)”
E601032 “Axis Driver:| Failed alarm clear.(ZT1)”
“排除警报失败。(ZT1)”
E601033 “Axis Driver:| Failed alarm clear.(ZT2)”
“排除警报失败。(ZT2)”
E601034 “Axis Driver:| Failed alarm clear.(ZT3)”
“排除警报失败。(ZT3)”
E601035 “Axis Driver:| Failed alarm clear.(ZT4)”
“排除警报失败。(ZT4)”
E601040 “Axis Driver:| Failed CAL.BLOCK mark Recognition. (L-OCC)”
“识别校准块标记失败。(L-OCC)”
E601041 “Axis Driver:| Failed CAL.BLOCK mark Recognition. (R-OCC)”
“识别校准块标记失败。(R-OCC)”
E601042 “Axis Driver:| Return to origin non-completion.”
“尚未完成返回原点。”
E601043 “Axis Driver:| Servo free.”
“伺服处于不使用状态。”
E601044 “Axis Driver:| XH-axis Irregular Position.”
“LSC 位置不对。”
E601045 “Axis Driver:| Please move LSC to the sensor position.”
“请把 LSC 移到传感器位置。”
E601046 “Axis Driver:| LSC communication error.”
“LSC 通讯失败。”
E601047 “Axis Driver:| The state of can the use of the XH-axis it is improper.”
“XH 轴的使用状态不对。”