JUKI贴片机错误代码集合.pdf - 第37页
calculated one? ” “ 根据测量组件大小结果，算出的激 光高度和当前的值不相同。 | 是否更新？ ” Q241311 “The automatically tombst one height is different from t he current v alue.|Change to the calcu lated one? ” “ 根据测量组件大小结果，算出的芯 片站立判断高度和当前的值不相 同。 | 是否更新？ …
给角度有错，是否把测量结果作为有效？”
[Cause]
The shorter side of the component has to be detected first in the outline measurement. However, the
longer side is detected first so the relation between the longer side and the shorter side does not meet
that of the Component data. There is a possibility that setting of component size or the feeding angle
is wrong.
1): The first component width detected.
2): The lengthwise component size in the Component data.
3): The second component width detected.
4): The widthwise component size in the Component data.
[Treatment]
Please check the component size and the feeding angle in the Component data.
E241307 “The inspection error occurred. Do you start single inspection?”
“检查发生错误，是否实行单独检查？”
[Cause]
When an inspection error occurred during the continuous inspection, you are asked if to perform a
single inspection for a component that is a cause of the error.
[Treatment]
'YES' button will take you to the screen where you can perform the a single inspection for the
component.
'NO' button will take you to the screen where you can inspect the next Component.
Q241308 “Is the measurement ended?”
“是否结束测量？”
[Cause]
You are asked if to close the Measurement screen of the single/continuous measurement.
[Treatment]
'YES' button will end the measurement. 'NO' button will cancel to end the measurement and will go
back to the Measurement screen.
Q241309 “Is the inspection ended?”
“是否结束检查？ “
[Cause]
You are asked if to close the Examination screen of the single/continuous inspection.
[Treatment]
'YES' button will end the inspection. 'NO' button will cancel to end the inspection and will go back to
the Examination screen.
Q241310 “The automatically calculated laser height is different from the current value.|Change to the
calculated one?”
“根据测量组件大小结果，算出的激光高度和当前的值不相同。|是否更新？”
Q241311 “The automatically tombstone height is different from the current value.|Change to the calculated
one?”
“根据测量组件大小结果，算出的芯片站立判断高度和当前的值不相同。|是否更新？”
E241500 “There is no verification device”
“不存在数值检查装置。”
[Cause]
Verification cannot be performed since there is no verification device installed.
[Treatment]
Please check the installation of the verification device (an option in MS parameter).
E241501 “The verification device is an unused unit”
“数值检查装置没有被选用。”
[Cause]
Verification cannot be performed since the verification device is set to “not use”.
[Treatment]
Please check the use status of the device (the Use unit in the Machine Setup).
E241502 “Supply of the component is no CVS”
“不存在适用 CVS 的组件。”
[Cause]
You are trying to verify a component that is not set to 'Verification' in the Expansion screen in Editor.
[Treatment]
Please set necessary items (Expansion screen in the Edit and Component data) for the Verification.
E241503 “The inspection error occurred”
“检查发生错误。”
[Cause]
This message appears to inform you that an error occurred during the Verification single inspection.
[Treatment]
Please press 'OK' button.
E241600 “Centering of the component is no vision.”
“不属于外形定中心组件。”
E241650 “Centering of the component is no lsc.”
“不属于 LSC 定中心组件。”
E241700 “There is no SOT direction inspection stage.”
“不存在 SOT 方向检查器。”
E241701 “The SOT direction inspection stage is an unuse unit.”
“SOT 方向检查器没有被选用。”
E241702 “The inspection error occurred.”
“检查发生错误。”
E241703 “The component size is out of range.”
“组件大小超出检查范围。”
Q241800 “%s|The optimum value of lighting data was acquirable.|(The basis in a prenthesis)|Is lighting data
updated?”
“%s|得到照明数据的优化值(括号内的是过去值)。| 是否更新照明数据? “
E241801 “The optimum value of lighting data was unacquirable.”
“不能取得照明数据的优化值。”
Q241802 “%sThe optimum value of light was acquirable.|(The basis in a prenthesis)|There is the influence of
inspection.Is lighting data updated?” 取得照明数据的优化值(括号内的是过去值)。|BGA 组
件的时候, 有时对检查精度有影响。|是否更新照明数据? “
E241900 “Coplanarity inspection is not specified.”
“没有指定共面检测器。”
E241901 “Coplanarity data was unacquirable. |Please confirm the height of component and lead width.”
“不能取得共面参数。|请确认一下组件高度和电极宽度。”
Q241902 “E.Brighthess Threshold %s (%s)|Scanning Offset %s (%s)|The optimum value of coplanarity
parameters was acquirable.|Is coplanarity parameters updated?”
“电极亮度阈值 %s (%s)|扫描位置的偏差 %s (%s)| 得到共面参数的优化值，是否更新参
数？”
E241903 “Centering of the component is no vision or lsc.”
“不属于外形定中心或 LSC 定中心的组件。 “
E242500 “The origin point return does not end.|Please retry after completing the origin point return.”
“未结束返回原点。|返回原点结束后，请再次运行。”
E242501 “The servo motor is free.|Please retry after releasing the servo free state.”
“伺服马达处于未起动状态。|请起动伺服马达后，再次运行。”
E242502 “Axis movement error (XY axis limit error)”
“轴移动发生错误(XY 轴界限错误)”