JUKI贴片机错误代码集合.pdf - 第232页

E613015 “ An error occur red when starting LZ3 axis movement .” “ LZ3 轴开始移动时发生错误。 ” E614015 “ An error occur red when starting LZ4 axis movement .” “ LZ4 轴开始移动时发生错误。 ” E615015 “ An error occur red when starting RZ1 axis …

100%1 / 464
A nozzle returning was requested while the vacuum of the right head2 is still ON. There is a
possibility that a component is being picked by the head.
右 Head2 的真空被启动的状态下要放回吸嘴。吸嘴上可能附有组件。
[Treatment]
Please take the component off the head, then turn off the vacuum before returning the nozzle.
检查 Head 上有没有组件被贴上，如果真有组件被贴上，请取下 Head 上的组件。
E610406 “Vacuum of R3 head has been on”
“R3 Head 真空被启动。”
[Cause]
A nozzle returning was requested while the vacuum of the right head3 is still ON. There is a
possibility that a component is being picked by the head.
右 Head3 的真空被启动的状态下要放回吸嘴。吸嘴上可能附有组件。
[Treatment]
Please take the component off the head, then turn off the vacuum before returning the nozzle.
检查 Head 上有没有组件被贴上，如果真有组件被贴上，请取下 Head 上的组件。
E610407 “Vacuum of R4 head has been on”
“R4 Head 真空被启动。”
[Cause]
A nozzle returning was requested while the vacuum of the right head4 is still ON. There is a
possibility that a component is being picked by the head.
右 Head4 的真空被启动的状态下要放回吸嘴。吸嘴上可能附有组件。
[Treatment]
Please take the component off the head, then turn off the vacuum before returning the nozzle.
检查 Head 上有没有组件被贴上，如果真有组件被贴上，请取下 Head 上的组件。
E610408 “The specified nozzle has been installed”
“指定吸嘴已经被安装。”
[Cause]
The nozzle requested to be installed has been already loaded on the head. The request of the nozzle
installation is not necessary.
指定的吸嘴已经都安装在 Head 上，没有必要再安装。
[Treatment]
This process can not be performed.
E611015 “An error occurred when starting LZ1 axis movement.”
“LZ1 轴开始移动时发生错误。”
E612015 “An error occurred when starting LZ2 axis movement.”
“LZ2 轴开始移动时发生错误。”
E613015 “An error occurred when starting LZ3 axis movement.”
“LZ3 轴开始移动时发生错误。”
E614015 “An error occurred when starting LZ4 axis movement.”
“LZ4 轴开始移动时发生错误。”
E615015 “An error occurred when starting RZ1 axis movement.”
“RZ1 轴开始移动时发生错误。”
E616015 “An error occurred when starting RZ2 axis movement.”
“RZ2 轴开始移动时发生错误。”
E617015 “An error occurred when starting RZ3 axis movement.”
“RZ3 轴开始移动时发生错误。”
E618015 “An error occurred when starting RZ4 axis movement.”
“RZ4 轴开始移动时发生错误。”
E611016 “An error occurred when starting LT1 axis revolution.”
“Lθ1 轴开始旋转时发生错误。”
E612016 “An error occurred when starting LT2 axis revolution.”
“Lθ2 轴开始旋转时发生错误。”
E613016 “An error occurred when starting LT3 axis revolution.”
“Lθ3 轴开始旋转时发生错误。”
E614016 “An error occurred when starting LT4 axis revolution.”
“Lθ4 轴开始旋转时发生错误。”
E615016 “An error occurred when starting RT1 axis revolution.”
“Rθ1 轴开始旋转时发生错误。”
E616016 “An error occurred when starting RT2 axis revolution.”
“Rθ2 轴开始旋转时发生错误。”
E617016 “An error occurred when starting RT3 axis revolution.”
“Rθ3 轴开始旋转时发生错误。”
E618016 “An error occurred when starting RT4 axis revolution.”
“Rθ4 轴开始旋转时发生错误。”
E611021 “An error occurred while LZ1 axis is traveling.”
“LZ1 轴开始移动时发生错误。”
E612021 “An error occurred while LZ2 axis is traveling.”
“LZ2 轴开始移动时发生错误。”
E613021 “An error occurred while LZ3 axis is traveling.”
“LZ3 轴开始移动时发生错误。”
E614021 “An error occurred while LZ4 axis is traveling.”
“LZ4 轴开始移动时发生错误。”
E615021 “An error occurred while RZ1 axis is traveling.”
“RZ1 轴开始移动时发生错误。”
E616021 “An error occurred while RZ2 axis is traveling.”
“RZ2 轴开始移动时发生错误。”
E617021 “An error occurred while RZ3 axis is traveling.”
“RZ3 轴开始移动时发生错误。”
E618021 “An error occurred while RZ4 axis is traveling.”
“RZ4 轴开始移动时发生错误。”
E611022 “An error occurred while LT1 axis is revolving.”
“Lθ1 轴开始旋转时发生错误。”
E612022 “An error occurred while LT2 axis is revolving.”
“Lθ2 轴开始旋转时发生错误。”
E613022 “An error occurred while LT3 axis is revolving.”
“Lθ3 轴开始旋转时发生错误。”
E614022 “An error occurred while LT4 axis is revolving.”
“Lθ4 轴开始旋转时发生错误。”
E615022 “An error occurred while RT1 axis is revolving.”
“Rθ1 轴开始旋转时发生错误。”
E616022 “An error occurred while RT2 axis is revolving.”
“Rθ2 轴开始旋转时发生错误。”
E617022 “An error occurred while RT3 axis is revolving.”
“Rθ3 轴开始旋转时发生错误。”
E618022 “An error occurred while RT4 axis is revolving.”
“Rθ4 轴开始旋转时发生错误。”