JUKI贴片机错误代码集合.pdf - 第305页
E640098 “ MTC SYSTEM ERROR (E098) : Door and Cover SW Error .” “ MTC 系统错误 (E098) : 机箱门或盖子的开关发生错误 ” E640099 “ MTC SYSTEM ERROR (E0 99) : Over Run Error .” “ MTC 系统错误 (E099) : 超出范围 ” E640100 “ MTC SYSTEM ERROR (E100) : Z A…
“MTC 系统错误(E078) : 没有初始化”
E640079 “MTC SYSTEM ERROR (E079) : Main Emergency Stop Switch is Pressed.”
“MTC 系统错误(E079) : 主机被紧急停止”
E640080 “MTC SYSTEM ERROR (E080) : Over Run Error (Z Axis Minus Limit).”
“MTC 系统错误(E080) : 超出范围错误(Z 轴负界限)”
E640081 “MTC SYSTEM ERROR (E081) : Over Run Error (X Axis Minus Limit).”
“MTC 系统错误(E081) : 超出范围错误(X 轴负界限)”
E640082 “MTC SYSTEM ERROR (E082) : Over Run Error (Y Axis Minus Limit).”
“MTC 系统错误(E082) : 超出范围错误(Y 轴负界限)”
E640083 “MTC SYSTEM ERROR (E083) : No.1 Head Sensor Error.”
“MTC 系统错误(E083) : No.1 Head 传感器发生错误”
E640084 “MTC SYSTEM ERROR (E084) : Over Run Error (Shuttle Minus Limit).”
“MTC 系统错误(E084) : 超出范围错误(滑梭负界限)”
E640087 “MTC SYSTEM ERROR (E087) : Interlock Error.”
“MTC 系统错误(E087) : 互锁错误”
E640090 “MTC SYSTEM ERROR (E090) : Unmovable (Z Axis).”
“MTC 系统错误(E090) : 不能移动(Z 轴)”
E640091 “MTC SYSTEM ERROR (E091) : Unmovable (X Axis).”
“MTC 系统错误(E091) : 不能移动(X 轴)”
E640092 “MTC SYSTEM ERROR (E092) : Unmovable (Y Axis).”
“MTC 系统错误(E092) : 不能移动(Y 轴)”
E640093 “MTC SYSTEM ERROR (E093) : No.2 Head Sensor Error.”
“MTC 系统错误(E093) : No.2 Head 传感器发生错误”
E640094 “MTC SYSTEM ERROR (E094) : Unmovable (Shuttle).”
“MTC 系统错误(E094) : 不能移动(滑梭)”
E640098 “MTC SYSTEM ERROR (E098) : Door and Cover SW Error.”
“MTC 系统错误(E098) : 机箱门或盖子的开关发生错误”
E640099 “MTC SYSTEM ERROR (E099) : Over Run Error.”
“MTC 系统错误(E099) : 超出范围”
E640100 “MTC SYSTEM ERROR (E100) : Z Axis Sensor Error.”
“MTC 系统错误(E100) : Z 轴传感器发生错误”
E640101 “MTC SYSTEM ERROR (E101) : X Axis Sensor Error.”
“MTC 系统错误(E101) : X 轴传感器发生错误”
E640102 “MTC SYSTEM ERROR (E102) : Y Axis Sensor Error.”
“MTC 系统错误(E102) : Y 轴传感器发生错误”
E640106 “MTC SYSTEM ERROR (E106) : RAM Error.”
“MTC 系统错误(E106) : RAM 错误”
E640107 “MTC SYSTEM ERROR (E107) : Break Current Error.”
“MTC 系统错误(E107) : 制动电流异常”
E640108 “MTC SYSTEM ERROR (E108) : Holder Sensor Error (Y Axis).”
“MTC 系统错误(E108) : 固定传感器发生错误(Y 轴).”
E640109 “MTC SYSTEM ERROR (E109) : Motor Off.”
“MTC 系统错误(E109) : 马达被关闭”
E640110 “MTC SYSTEM ERROR (E110) : Software Limit (Z Axis).”
“MTC 系统错误(E110) : 软件界限(Z 轴)”
E640111 “MTC SYSTEM ERROR (E111) : Software Limit (X Axis).”
“MTC 系统错误(E111) : 软件界限(X 轴)”
E640112 “MTC SYSTEM ERROR (E112) : Software Limit (Y Axis).”
“MTC 系统错误(E112) : 软件界限(Y 轴)”
E640114 “MTC SYSTEM ERROR (E114) : Shuttle Sensor Error.”
“MTC 系统错误(E114) : 滑梭传感器发生错误”
E640116 “MTC SYSTEM ERROR (E116) : NV-RAM Error.”
“MTC 系统错误(E116) : NV-RAM 发生错误”
E640117 “MTC SYSTEM ERROR (E117) : Shutter Close/Open Sensor Error.”
“MTC 系统错误(E117) : 滑梭打开/关闭传感器发生错误”
E640120 “MTC SYSTEM ERROR (E120) : Drive Time Out (Z Axis).”
“MTC 系统错误(E120) : 驱动超时(Z 轴)”
E640121 “MTC SYSTEM ERROR (E121) : Driver Alarm (X Axis).”
“MTC 系统错误(E121) : 驱动警报(X 轴)”
E640122 “MTC SYSTEM ERROR (E122) : Driver Alarm (Y Axis).”
“MTC 系统错误(E122) : 驱动警报(Y 轴)”
E640124 “MTC SYSTEM ERROR (E124) : Driver Alarm (Shuttle).”
“MTC 系统错误(E124) : 驱动警报(滑梭)”
E640127 “MTC SYSTEM ERROR (E127) : Tray Error.”
“MTC 系统错误(E127) : 托盘错误”
E640130 “MTC SYSTEM ERROR (E130) : Position Error (Z Axis).”
“MTC 系统错误(E130) : 位置错误”
E640134 “MTC SYSTEM ERROR (E134) : Changing Shuttle Pad Error.”
“MTC 系统错误(E134) : 更换滑梭垫发生错误”
E640140 “MTC SYSTEM ERROR (E140) : Unable to Change Servo Driver ON (Z Axis).”
“MTC 系统错误(E140) : 不能起动伺服驱动器(Z 轴)”
E640144 “MTC SYSTEM ERROR (E144) : Software Limit (Shuttle).”
“MTC 系统错误(E144) : 软件界限(滑梭)”
E640150 “MTC SYSTEM ERROR (E150) : Servo Alarm.”
“MTC 系统错误(E150) : 伺服警告”
E640164 “MTC SYSTEM ERROR (E164) : Bulb Error.”
“MTC 系统错误(E164) : Bulb 错误”
I640170 “MTC : Drawing Parts Cancel by parts request cancellation.”
“MTC : 取组件的要求，因状态转为取消而被取消”
I640181 “MTC : Drawing Parts Cancel by Switching Off-line.”
“MTC : 取组件的要求，因状态转为脱机而被取消”
I640182 “MTC : Drawing Parts Cancel by Switching Supply.”
“MTC : 取组件的要求，因状态转为补充而被取消”