2OM-1104-001.pdf - 第170页

Error ID Item Description 0217000 T able Z Interlock (-) Limit error has been detected. (Cause 1) The table θ limit (-) photosensor (BPH213) is defective. (Cause 2) The operation timing is shifted from the normal one. (C…

100%1 / 387
Error ID Item Description
0214000 Table Z Interlock Table-X Axis approached interlock area.
(Cause 1) The table X-axis interlock sensors (BPH056 and BPH057) are defective.
(Cause 2) The operation timing is shifted from the normal one.
(Remedy 1) Check how the sensors are working in “Device Check” window (submenu).
When the sensors are not working, it is required to replace the sensors
with new ones. Contact our service personnel for details.
(Remedy 2) Shut down the power of the machine once and power up the machine
again. After that, restart the operation.
When the same error still occurs, contact our service personnel for de-
tails.
0216000 Table Z Interlock (+) Limit error has been detected.
(Cause 1) The table θ−axis limit (+) photosensor (BPH212) is defective.
(Cause 2) The operation timing is shifted from the normal one.
(Cause 3) The table Z axis was activated while the table θ axis was moving wildly.
(during the manual operation)
(Remedy 1) Check how the sensor is working in “Device Check” window (submenu).
When the sensor is not working, it is required to replace the sensor with
a new one. Contact our service personnel for details.
(Remedy 2) Shut down the power of the machine once and power up the machine
again. After that, restart the operation.
When the same error still occurs, contact our service personnel for de-
tails.
(Remedy 3) Perform the zeroing operation and re-start the operation.
2.3 Error IDs and Remedial Procedures
0106-002 Chapter 2 2 14 AFU01ETRP
Error ID Item Description
0217000 Table Z Interlock (-) Limit error has been detected.
(Cause 1) The table θ limit (-) photosensor (BPH213) is defective.
(Cause 2) The operation timing is shifted from the normal one.
(Cause 3) When this error occurs during a manual operation, it is not regarded as a
device error.
(Remedy 1) Check how the sensor is working in “Device Check” window (submenu).
When the sensor is not working, it is required to replace the sensor with
a new one. Contact our service personnel for details.
(Remedy 2) Shut off the power to the machine once and power up the machine again.
After that, re-start the operation.
When the same error still occurs, contact our service personnel for de-
tails.
(Remedy 3) Perform the zeroing operation and re-start the operation.
0218000 Table Z Interlock P.E.C Recog-Y Axis is not at safety area.
(Cause 1) The P.E.C. recognition Y-axis interlock sensor (BPH046) is defective.
(Cause 2) The operation timing is shifted from the normal one.
(Cause 3) The table Z axis was activated when the P.E.C. recognition Y-axis was not
located at its rear escape position.
(during the manual operation)
(Remedy 1) Check how the sensor is working in “Device Check” window (submenu).
When the sensor is not working, it is required to replace the sensor with
a new one. Contact our service personnel for details.
(Remedy 2) Shut down the power of the machine once and power up the machine
again. After that, restart the operation.
When the same error still occurs, contact our service personnel for de-
tails.
(Remedy 3) Perform the zeroing operation and re-start the operation.
2.3 Error IDs and Remedial Procedures
0106-002 Chapter 2 2 15 AFU01ETRP
Error ID Item Description
0219000 Table Z Timing Task has not been completed unable to continue.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
If the machine is not reset to its normal condition, shut down the power of
the machine once and power up the machine again. After that, re-start
the operation.
When the same error still occurs, contact our service personnel for de-
tails.
0220000 Table Z Data The data was detected outside of the possible range.
(Cause 1) The specified data may have exceeded the movable range.
(Remedy 1) Check the parameters in the “Screen Distance” (“Pattern Program” win-
dow), “Screen Distance” (“OFFSET DATA” window), and “P.C.B. Trans-
fer Height” (“OFFSET DATA” window) text boxes.
0221000 Table Z Origin Zeroing Opn. Not Complete
(Cause 1) The motor axis was activated before the zeroing operation was completed.
(Remedy 1) Perform the zeroing operation.
0301000 Table
θθ
θθ
θ Origin Zeroing opn. was incompleted, within specified time.
(Cause 1) Dirt adheres to the sensor and the optical beam is shielded.
(Cause 2) The sensor is defective.
(Cause 3) The driver is malfunctioning or an error has occurred during communication
with the host CPU.
(Remedy 1) Wipe off dirt on the sensor and zero Table θ again.
(Remedy 2) It is required to replace the sensor with a new one. Contact our service
personnel for details.
(Remedy 3) Shut down the power of the machine once and power up the machine
again. After that, perform the zeroing operation.
If this operation does not reset the machine to its normal condition, the
driver may be defective. Contact our service personnel for details.
2.3 Error IDs and Remedial Procedures
0106-002 Chapter 2 2 16 AFU01ETRP