2OM-1104-001.pdf - 第223页
Error ID Item Description 2005000 Cleaning Cleaning nozzle up/down cylinder moving error (Cause 1) The cleaning nozzle was moved up when the P .C.B. recognition Y axis was not located at its front escape position (origin…
Error ID Item Description
1904000 Screen Recognition (Same as "Fiducial Mark #1")
Test
(Cause 1) Same as "Fiducial Mark #1"
(Remedy 1) Same as "Fiducial Mark #1"
1906000 Screen Recognition (Same as "Fiducial Mark #1")
Camera
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Shut down the power of the machine once and power up the machine
again. After that, restart the operation.
When the same error still occurs, contact our service personnel for de-
tails.
2001000 Cleaning Interlock P.E.C Recog-Y Axis is not at safety area.
(Cause 1) The cleaning nozzle was moved up when the P.C.B. recognition Y axis was
not located at its front escape position (origin position).
(during the manual operation)
(Cause 2) The P.C.B. recognition Y-axis near origin sensor (BPH331) is defective.
(Cause 3) The operation timing is shifted from the normal one.
(Remedy 1) Zero the P.C.B. recognition Y axis and re-start the operation.
(Remedy 2) Zero the P.C.B. recognition Y axis.
When the P.C.B. recognition Y axis cannot be zeroed, it is required to
replace the sensor with a new one. Contact our service personnel for
details.
(Remedy 3) Shut down the power of the machine once and power up the machine
again. After that, restart the operation.
When the same error still occurs, contact our service personnel for de-
tails.
2.3 Error IDs and Remedial Procedures
0106-001 Chapter 2 2 67 AFU01ETRP
Error ID Item Description
2005000 Cleaning Cleaning nozzle up/down cylinder moving error
(Cause 1) The cleaning nozzle was moved up when the P.C.B. recognition Y axis was
not located at its front escape position (origin position).
(during the manual operation)
(Cause 2) The P.C.B. recognition Y-axis near origin sensor (BPH331) is defective.
(Cause 3) The operation timing is shifted from the normal one.
(Remedy 1) Zero the P.C.B. recognition Y axis and re-start the operation.
(Remedy 2) Zero the P.C.B. recognition Y axis.
When the P.C.B. recognition Y axis cannot be zeroed, it is required to
replace the sensor with a new one. Contact our service personnel for
details.
(Remedy 3) Shut down the power of the machine once and power up the machine
again. After that, restart the operation.
When the same error still occurs, contact our service personnel for de-
tails.
2006000 Cleaning Cleaning paper feed error
(Cause 1) The paper feeder pitch detection sensor (BPH082) is not working.
(Cause 2) The inside of the cleaning paper roller is torn, making the rotation of the
paper cylinder idle.
(Cause 3) The belt of the take-up motor is not engaged correctly (some teeth not mesh-
ing with the belt).
(Remedy 1) Check for any dirt around the sensor and how the sensor is working in
the "DEVICE CHECK" window (submenu).
When the sensor is not working, it is required to adjust the sensor posi-
tion or replace the sensor with a new one.
Contact our service personnel for details.
(Remedy 2) Check the internal condition of the paper roller. If some area is torn, re-
place it with another one.
(Remedy 3) When you hear the sounds, indicating that some teeth do not mesh cor-
rectly with the belt during the take-up operation, it is required to adjust the
belt tension.
Contact our service personnel for details.
2.3 Error IDs and Remedial Procedures
0106-001 Chapter 2 2 68 AFU01ETRP
Error ID Item Description
2102000 Operator's Error P.C.B. was took on inp. conveyor.
(Cause 1) Although a manual operation cannot be implemented with a P.C.B. on the
input conveyor, such an operation was performed with a P.C.B.
(Remedy 1) Remove the P.C.B. on the input conveyor and re-start the operation.
2103000 Operator's Error P.C.B. removed from input conveyor.
(Cause 1) Although a manual operation cannot be implemented without a P.C.B. on
the input conveyor, such an operation was performed without a P.C.B.
(Remedy 1) Place a P.C.B. on an area of the input conveyor where the sensor reacts.
2105000 Operator's Error Vacuum plate was not found.
(Cause 1) The automatic or the manual operation was performed without any pattern
program specified as a current one.
(Remedy 1) Perform a program change operation.
2106000 Operator's Error P.C.B. was took on table.
(Cause 1) Although a manual operation cannot be implemented with a P.C.B. on the
table, such an operation was performed with a P.C.B.
(Remedy 1) Remove the P.C.B. on the table and re-start the operation.
Click the table section (illustrated) in the "AUTO OPN." window to re-
move the P.C.B. from the memory of the machine whenever necessary.
2107000 Operator's Error P.C.B. removed from table.
(Cause 1) Although a manual operation cannot be implemented without a P.C.B. on
the table, such an operation was performed without a P.C.B.
(Remedy 1) Place a P.C.B. on the table and re-start the operation.
Click the table section (illustrated) in the "AUTO OPN." window to set the
P.C.B. in the memory of the machine whenever necessary.
2.3 Error IDs and Remedial Procedures
0106-001 Chapter 2 2 69 AFU01ETRP