CAN Bus Workshop_Version 03__06-2008_EN.pdf - 第122页

1 Caccia Student Guide CACCIA Manual Issue 04/2007 EN 30 1.4.3.1 1. Operating Mode: Endurance T est for Linear Axes (From T op Lef t to Bottom Right) This mode is active when Chopping has not been ticked. 1 This mode als…

100%1 / 298
CACCIA Manual 1 Caccia Student Guide
Issue 04/2007 EN
29
1.4.3 Axis Endurance Test Dialog Box
There are three operating states for the Axis Endurance dialog box: 1
1
Tab. 1 - 8 Axis endurance dialog box functions
There are two operating states for the Axis Endurance dialog box: 1
– Endurance test for linear axes
– Endurance test for rotary axes
The following operating elements are the same in both states: 1
1
Fig. 1 - 16 Axis endurance dialog box functions
Button Description / Action
White arrow No action has been started
Yellow arrow Positioning in progress
Red arrow
Either an error has occurred (you may need to acknowledge the error
and perform a ref. run) or the axis has been stopped by the operator.
Maximum
number of
positioning runs
Shows how many
positioning runs have
already been performed
Waiting period
Set the axis traveling
speed in % here
(Default = 100%)
Shows the minimum/
maximum position which
the axis may travel to
Shows the
positioning time
deactivated:
Endurance test for linear axes
activated:
Endurance test for rotary axes
Goto Start
The axis moves to the start position
Goto End
The axis moves to the end position
Step
The axis moves in single steps
from the end position to the start
position or vice versa
Start
Starts the endurance test. The selected
axis travels continuously between the
specified start and end positions, in line
with the set parameters
Stop Soft and Stop Cycle
Stop buttons for the started endurance
test.
Resets the
value in the
Count field
1 Caccia Student Guide CACCIA Manual
Issue 04/2007 EN
30
1.4.3.1 1. Operating Mode: Endurance Test for Linear Axes (From Top Left to Bottom Right)
This mode is active when Chopping has not been ticked. 1
This mode also has the following special operating elements: 1
1
Fig. 1 - 17 1. operating mode: operating elements
Enter the travel profile for
the axis path (go).
Starting position plus
length gives end position
or
Starting position plus end
position gives positioning
length
Enter the travel profile for
the axis path (return).
Operating mode:
Endurance test for linear
Axes
CACCIA Manual 1 Caccia Student Guide
Issue 04/2007 EN
31
1.4.3.2 2. Operating Mode: Endurance test for Rotary Axes (e.g. Star)
To switch over to this mode, set a tick at Chopping. If linear axes are to be operated as „rotary
axes“, move the axes from the end of the travel area back to the beginning with selected speed.1
This mode also has the following special operating elements: 1
1
1
Fig. 1 - 18 1. operating mode: operating elements
1.4.4 How to Perform an Axis Reference Run
→ Doubleclick on the required axis in the Subsystem Control Center. This opens the Axis dialog
box.
→ Set a tick at Query to enable the query option. The status display will change.
→ Open the Axis Data dialog box with the button.
Note
Copy the current axis data (ma_achsen.mdb) from the station computer to the laptop (via
data carrier) and use this data. This ensures that you access the correct database for the axis
data. 1
→ Click on the Load from Database button. This opens a window in which the required data can
be selected. Specify the copied data here.
→ Click on the Geometric Data button.
Enter the travel profile for
the axis path.
Starting position and n x
length gives the end
position of each step for
the star axis.
Operating mode:
Endurance test for rotary
Axes