00191413-01.pdf - 第30页

1 Hardware / Software Installati on User Manu al Line Computer UNIX 1.2 Software Install ation Software Version 501.xx 01/99 Issue 1 - 12 NOTE Only i n cases whe re a sec ond LAN c ard for the SIPLA CE LAN is insta lled …

100%1 / 621
User Manual Line Computer UNIX 1 Hardware / Software Installation
Software Version 501.xx 01/99 Issue 1.2 Software Installation
1 - 11
After converting the GF-Bibliothek (package form library), the selection possibilities for the configuration
of the desktop ("Desk-Configuration") are displayed on the screen.
1) Programming
2) Controlling
Enter a value in between [1-2]:
Enter
1
if the desktop (see chapt. 3) is to be set up as a programming station, or enter
2
if the desktop
is to be set up as a control station, and confirm your entry by pressing RETURN.
A menu for the selection of a production line (example) is displayed only if line configurations exist (see
chapt. 12, section 12.2.1):
1) SMT
2) ERP_L2
Please select a line [1-2]:
● Enter number of line (e.g.
1
for SMT) and press RETURN.
Do you want to configure the LRU software for line SMT [y/n]:
● Enter
y
and press RETURN.
The line is configured.
A list containing the allocations of the time zone settings is displayed ("Timezone-Configuration").
Select a timezone [1-12]:
● Enter number of time zone desired and confirm by pressing RETURN.
Now the language to be used by the LC system when it is started up can be selected ("Language-
Configuration").
(1) D = Deutsch (German) 2) F = French 3) GB = English 4) I = Italian )
Enter a value in between [1-4]:
● Enter number of language desired and confirm by pressing RETURN.
1 Hardware / Software Installation User Manual Line Computer UNIX
1.2 Software Installation Software Version 501.xx 01/99 Issue
1 - 12
NOTE
Only in cases where a second LAN card for the SIPLACE LAN is installed in the line computer, will
the IP address, netmask and broadcast address of the LAN card for the SIPLACE LAN be displayed
together with an inquiry as to whether they are to be changed.
● Enter
y
and press RETURN if the data are to be changed.
Enter internet address for SIPLACE network card
(<Return> for default....):
● Enter the address and press RETURN.
The entry is displayed.
Is the internet address ’...’ correct [y/n]:
● Enter
y
and press RETURN if the entry is correct.
(Enter
n
and press RETURN if the entry needs to be corrected).
Enter netmask for SIPLACE network card
(<Return> for default....):
● Enter the number of the "netmask" and press RETURN.
The entry is displayed.
Is the netmask ’...’ correct [y/n]:
● Enter
y
and press RETURN if the entry is correct.
(Enter
n
and press RETURN if the entry needs to be corrected).
Enter broadcast address for SIPLACE network card
(<Return> for default....):
● Enter the number of the "broadcast address" and press RETURN.
The entry is displayed.
Is the broadcast address ’...’ correct [y/n]:
● Enter
y
and press RETURN if the entry is correct.
(Enter
n
and press RETURN if the entry needs to be corrected).
The entry of
y
completes the configuration of the LAN card.
User Manual Line Computer UNIX 1 Hardware / Software Installation
Software Version 501.xx 01/99 Issue 1.2 Software Installation
1 - 13
A note is now displayed on the handling regarding OEM software, as well as the steps to be per-
formed following the start of the LC program (consistency check via Data Manager of setups and
line configuration).
● Read the messages and acknowledge them by pressing any key.
After a short time a message is displayed on the screen requesting you to reboot the system.
** Safe to Power Off **
- or -
** Press Any Key to Reboot **
● Remove CD-ROM and press any key on the keyboard.
The computer system reboots.
CAUTION
In the event that the boot diskette (see page 1 - 7) used for the SW installation was not the correct
one, an error message will be displayed during the shutdown process (prior to “Safe to Power Off”).
Upon the subsequent booting of the computer, the following queries have to be answered:
There may be a system dump memory image in the swap device!
Do you want to save a copy of it?
[y/n]
● Enter
n
and press RETURN.
Do you want to remove the dump from the swap device now?
[y/n]
● Enter
y
and press RETURN
.
It is imperative that the two preceding questions be answered as indicated, as otherwise problems
with the operating system are likely to arise.
Okay to check the root filesystem
[y/n]
● Enter
y
and press RETURN
.
After a while, the "Login" dialog box (see chapt. 2, section 2.1.1) appears.
● Type
plr
in the "login" editing field and press the RETURN key.
● Type
plr
in the "Password" editing field and press the RETURN key.
The LC software is started with the selected desktop configuration and language.
ATTENTION !
After any initial installation of the LC software has been carried out, it is mandatory that following
start-up of the line computer the stations be configured with the aid of the Configuration Editor (see
chapt. 12) before proceeding further. Subsequently, the line must be configured with the aid of the Line
Editor (see chapt. 12).
Whenever an Update or Upgrade of the LC software is performed, it is absolutely necessary that
after the software has been started up, all set-ups be checked for consistency using the "Consistency
Checker" (see chapt. 4, section 4.3.4.6).