FlexTRAK OH Material Handler Manual.pdf - 第19页
FlexTRAK-OH Material Handli ng System IOM Manual Introductio n © 2023 Nordson C orporation 1-9 1.5.3 Strip Loa ding Buff er (Stn20) Item Name Description 1 Strips ID Reader Reads the strip identification data printed on …
FlexTRAK-OH Material Handling System IOM Manual Introduction
1-8 © 2023 Nordson Corporation
Item
Name
A1 Magazine Elevator Motor
B1 Loaded Magazine Gripper
B2 Empty Magazine Gripper
Figure 1-5 Loader Lifter (Stn20)
FlexTRAK-OH Material Handling System IOM Manual Introduction
© 2023 Nordson Corporation 1-9
1.5.3 Strip Loading Buffer (Stn20)
Item
Name
Description
1 Strips ID Reader
Reads the strip identification data printed on the surface of the strip,
as shown in Figure 1-14.
2 Axis 1: Y-Axis Actuator
Transfers the Loader Elevator Gripper in the Y-axis to the following
positions:
• Input Magazine Conveyor – magazine loading
• Strip Transfer Buffer Lanes
• Output Magazine Conveyor – magazine unloading
3
Cylinder 2002: Loader
Elevator Pitch Wheel
Positions the Loader Strip In Presence Sensor and the Loader Strip
Out Presence Sensor at the lane location.
4
Loader Strip Out Presence
Sensor
Confirms the kicked strip is presented inside the strip buffering lane.
5
Loader Strip In Presence
Sensor
Confirms the kicked strip is absented at the magazine strip slot.
6
Cylinder 2003: Loader
Elevator Kicker
Pushes the strips out of the magazine slots.
7
Loader Gripper Magazine
Presence Sensor
Ensures the magazine is flush with the gripper rear support plate.
8
Loader Elevator Strip
Counting Presence Sensor
Slot Mapping
Detects the presence of strips in the magazine slots. This feature will
allow the loader elevator kicker to skip the empty slots during the strip
kicking process.
9
Cylinder 2004: Loader
Elevator Zero Gap
Positions the magazine closer to the input buffer lane.
10
Loader Gripper Grip
Presence Sensor
Checks that the magazine is properly gripped.
11
Cylinder 2001: Loader
Elevator Gripper
Actuates the magazine gripper.
12 Axis 2: Z-Axis Actuator
Transfers the clamped magazine in the Z-axis to these positions:
• Input Magazine Conveyor - Magazine Loading
• Strip Transfer Buffer
• Output Magazine Conveyor - Magazine Unloading
13
Axis 10: X-Axis Actuator
Positions the loader elevator kicker to adjust the strip kicking gap.
Figure 1-6 Strip Loading Buffer (Stn20)
FlexTRAK-OH Material Handling System IOM Manual Introduction
1-10 © 2023 Nordson Corporation
1.5.4 Strip Transfer – Loading (Stn30)
Item Name Description
1
Axis 3 Actuator: Pinch Wheel
Roller In
Transfers an untreated strip to strip clawing position.
2
Loader Strip Through Present
Sensor
Checks that strips are not protruding into the gap between
magazine and input buffer lanes.
3
Transfer Input Buffer Pinch Wheel
Cylinder
Exerts pinching pressure through the pinch wheels onto
the strip. Correct pinch pressure ensures that sufficient
force is applied to the strip to effect transfer.
4 Conversion Kit: Input Buffer Lane
Input strip buffer conversion kit. Conversion kits are
specific to strip size.
5
Cylinder 3003: Input Transfer
Z-Axis
Elevates the input buffers to the same Z-axis position as
the plasma chamber rails to facilitate clawing of strips
into/out of plasma chamber.
6
Cylinder 3004: Input Transfer
X-Axis
Engages the Input Buffer Lanes with the plasma chamber
rails for "Zero Gap" transfer of strips.
Figure 1-7 Strip Transfer – Loading (Stn30)