FlexTRAK OH Material Handler Manual.pdf - 第34页
FlexTRAK-OH Material Handli ng System IOM Manual Safety 2-4 © 2023 Nordson C orporation 2.9 Safety Warning Labels Safety labels o n the FlexTRAK - OH Material Ha ndler point out pot entially haz ardous area s and remind …
FlexTRAK-OH Material Handling System IOM Manual Safety
© 2023 Nordson Corporation 2-3
• Where Volatile Organic Compound (VOC) emissions can exceed safe limits, facility
ventilation and filtration systems must be operational.
• Provide adequate space around the FlexTRAK-OH Material Handler to allow for movement
of maintenance and service personnel. Allow space for access doors and service panels to
open fully. Posing the body with the recommended posture and space clearance during
machine work task. See 8.5 Clearance Distance Requirement.
• Make sure all facility power sources are safely grounded.
• Routinely inspect all air hoses and electrical cables for damage.
• Make sure that the power cords and air supply hoses do not cross a walkway or aisle.
• Before attempting to lift a load, take into consideration facility lifting and transport
precautions.
• Maintain a clean, safe, and orderly work area, and immediately report any presence of
unsafe conditions to the authorized personnel.
2.5 Material Safety
• Follow Safety Data Sheet (SDS) recommendations for the proper handling, cleanup, and
disposal of hazardous materials.
• Knows the SDS recommendations for treatment of injury resulting from exposure to
hazardous materials.
• When working with multiple fluids, refer to the SDS to ensure the materials are compatible.
2.6 Preventing Workpiece Damage
• Immediately push the EMO button if the FlexTRAK-OH Material Handler or a workpiece
is in danger of being damaged.
• Use standard Electrostatic Discharge (ESD) precautions when working near sensitive
components. Always wear a grounding strap and connect it to the ESD ground before
handling work pieces.
• Immediately contain and clean up any caustic or conductive fluid spills as recommended in
the material manufacturer’s SDS. If fluid gets into internal portions of the machine,
immediately contact March for additional assistance.
• Follow all recommended system maintenance procedures.
• Always keep the FlexTRAK-OH Material Handler clear of any fallen work pieces or
obstacles.
• Ensure that no air intakes or exhaust grilles are blocked when the system is in operation.
2.7 Disposal
Dispose of equipment and materials used in operation and servicing in accordance with local regulations.
2.8 Earthquake Precautions
In the event of an earthquake, your FlexTRAK-OH Material Handler must be secured to prevent
movement that could cause injury to personnel and damage to the plasma system and facility. Each
leveler (foot) should be anchored to the floor. Refer to the FlexTRAK Series Plasma Systems Installation,
Operation, and Maintenance Manual for detailed information.
FlexTRAK-OH Material Handling System IOM Manual Safety
2-4 © 2023 Nordson Corporation
2.9 Safety Warning Labels
Safety labels on the FlexTRAK-OH Material Handler point out potentially hazardous areas and remind
personnel to take necessary safety precautions. Safety warning label are described in Table 2-1. Warning
label locations are shown in Figure 2-1 through Figure 2-4.
WARNING! Comply with all safety warning labels or serious injury to personnel or damage to
the system may occur. Worn or damaged labels should be replaced with new
labels.
Table 2-1 Safety Warning Labels
No.
Category
Label
Type
Safety Precaution
1
Mechanical
DANGER!
Crush Hazard
Keep hands clear while operating. Lock out
power before servicing.
2
WARNING!
Moving Parts
Present
Keep hands away from moving parts. Lock
out power before servicing.
3
WARNING!
Pinch Point and
Mechanical
Entanglement
Keep hands away from the machine. Lock out
power before servicing.
4
CAUTION!
Hot Surface
Do not touch. It can cause skin burns upon
contact. Allow the surface to cool and lock out
power before servicing.
5 Electrical
WARNING!
Hazardous
Voltage
Lock out power before servicing.
6 Laser
CAUTION!
Class 1 Invisible
Laser Radiation
Presence
This is a class 1 laser beam type. Laser
emission from this product is not automatically
stopped when it is dissembled. Do not have
direct eye contact with the laser beamline.
7 Radiation
WARNING!
Non-ionizing
radiation exists
inside
Exposure may cause body tissues damage.
Lock out power before servicing.
FlexTRAK-OH Material Handling System IOM Manual Safety
© 2023 Nordson Corporation 2-5
Figure 2-1 FlexTRAK-OH Overall Safety Hazard Label Locations (Top View)
Figure 2-2 Laser Beam Location 1 – Input Buffer Lane