1OM-1064-002.pdf - 第102页
1. Notes W ARNING 1. Do not keep the selection key inserted unless necessary . The key shall be stored by the person in charge. 2. Only the trained personnel shall operate the machine when the [OP- ERA TION/SET UP] switc…
1. Notes
• Either the front or the rear panel can be set available in operation by press-
ing the [PNL CHANGE] button on the unavailable side only when both are
not in “LOCK” mode.
Either one of the operation panels can be selected regardless of the opera-
tion mode (such as “RUN” and “PAUSE”) of the machine.
9910-001 2-3 Tg0246-PM-OP
CAUTION
When the [STOP] or the [PAUSE] button is pressed with the operation
lock LED (-HD06) OFF, the operation panel on the pressed button side is
automatically set available in operation.
• When the [OPERATION/SET UP] switch on the available side is set to the
“SET UP” side, the unavailable side is locked forcibly.
Note: When the [OPERATION/SET UP] switch on the unavailable side is
pressed, an error occurs.
To cancel the “LOCK” mode, set the [OPERATION/SET UP] switch to the
“OPERATION” side.
• Described in the table below is the ON/OFF relation between the LED (-
HD05) of the [PNL CHANGE] button and the operation lock LED (-HD06).
Table 2.1
Note: When power is supplied, the front operation panel including the touch
screen is set available in operation.
Front Operation Panel Rear Operation Panel
Mode
LED (-HD05) of
[PNL CHANGE]
Button
Operation Lock
LED (-HD06)
LED (-HD05)
of [PNL
CHANGE]
Button
Operation
Lock LED
(-HD06)
Front Panel Available in
Operation
ON OFF OFF OFF
Operations Available
Only with Front Panel
(Operation Locked)
ON ON OFF ON
Rear Panel Available in
Operation
OFF OFF ON OFF
Operations Available
Only with Rear Panel
(Operation Locked)
OFF ON ON ON
CAUTION
In principle, the machine must be operated by only one person.
If there are more than one, ensure good communication by giving loud
verbal instructions for safety purposes.
1. Notes
WARNING
1. Do not keep the selection key inserted unless necessary. The key
shall be stored by the person in charge.
2. Only the trained personnel shall operate the machine when the [OP-
ERATION/SET UP] switch is set to the “SET UP” side. Otherwise, it
may cause critical injury to the operator.
3. When the [OPERATION/SET UP] switch is set to the “SET UP” side,
the operator can operate the machine with the maintenance cover
open.
It is very dangerous to operate the machine without safety check. Be
sure to pay a special caution while operating the machine.
The [OPERATION/SET UP] switch must be kept in the “OPERATION”
side in normal cases to avoid any danger.
1.2 [OPERATION/SET UP] Switch
When the [OPERATION/SET UP] switch is set to the “SET UP” side, the
interlock functions of the maintenance/supply cover and the safety bar are
partly canceled, making it possible to perform set-up operations with the main-
tenance cover opened (limited to the actions taken without any X/Y beam move-
ment).
0004-002 2-4 Tg0246-PM-OP
• The [OPERATION/SET UP] switch becomes effective only when the fol-
lowing requirements are fulfilled.
(1) The machine must be set in the “STOP” mode.
(2) Operations must be performed on the operation available side.
(3) The maintenance/supply cover and the safety bar on the operation un-
available side must be closed.
(4) The up/down axis (LA1, LA2, LB1, and LB2 axis) on each beam must
be located at their origins (NEAR).
• The selection key must be used to change over the [OPERATION/SET UP]
switch.
• When the [OPERATION/SET UP] switch is set to the “SET UP” side, all
tower lights (red, yellow, and green) illuminate.
• When the [OPERATION/SET UP] switch is set to the “SET UP” side, the
power to drive the X/Y beam is shut off.
1. Notes
Operation Items
Operation
Possible/
Impossible
X Axis
×
Y Axis
×
Up/Down Shaft
×
Head Rotational Shaft
×
Manual Axis
Operation
Backup Up/Down Shaft
{
Movement to Target
Position
{
Set-Up
(Conveyor
Width)
Manual Axis Operation
{
Air Supply
(Beams A and B)
{
Manual
Subsystem
Operation
Pick-Up/Blowing
(LA1 and LA2 Axis,
LB1 and LB2 Axis)
{
P.C.B. Transfer
{
Backup Base
Movement
(Positioning, Standby,
and Origin Positions)
{
P.C.B. Locating Side
Clamp
{
L/P/R Conveyors
(Normal/Reverse
Rotation)
{
P/R Conveyor P.C.B.
Stopper
{
EL/ER Conveyors
(Normal/Reverse
Rotation)
{
Manual
Transfer
Operation
EL/ER Conveyer
P.C.B. Stopper
{
Teaching
×
Recognition Test
(P.C.B. and Component Recognition
Functions)
×
Automatic Operation
×
System Clear
×
ET Communication (RS-232C)
×
Tray Feeder (“Feeder Change-Over
Preparation Complete” Operation)
{
Operation Items
Operation
Possible/
Impossible
Operation on Available Operation Panel
Side
{
Operation on Unavailable Operation Panel
Side
×
Zeroing Operation
×
Backup Up/Down Shaft
{
Conveyor Width
Variable Shaft
{
Tray L and R
{
All Beams and Beams
A and B
×
X/Y Shaft
×
Head (Up/Down and
Rotational Shafts)
×
Up/Down Shaft
×
Head Rotational Shaft
×
Zeroing
Feeder Base
{
Traverse Shaft
{
Tray Feeder
Manual
Subsystem
Operation
(Zeroing
Operation)
Elevator Shaft
{
Traverse Shaft
{
Tray Feeder
Manual
Subsystem
Operation
(Manual
Operation)
Elevator Shaft
{
Tape Feed
{
L/P/R Conveyors
(Normal/Reverse
Rotation)
{
EL/ER Conveyors
(Normal/Reverse
Rotation)
{
Servomotor Adjustment
(X, Y)
×
Servomotor Adjustment
(L)
×
Unit Adjustment
Servomotor Adjustment
(Backup Up/Down
Shaft)
{
Case: The [OPERATION/SET UP] switch is set to the “SET UP”
side.
{ : Operation Possible
× : Operation Impossible
9910-001 2-5 Tg0246-PM-OP