1OM-1064-002.pdf - 第172页
2. AUTO OPN MODE (PLACEMENT) Display DEVI CE TEST DEVI CE TEST (PLACEM ENT) ( PASSAGE ) 9910-001 3-4 Tg0246-PM-OP *6 Normally the key is labeled as follows. CAUTION Do not perform automatic operation when the key is labe…
2. AUTO OPN MODE (PLACEMENT) Display
2. AUTO OPN MODE (PLACEMENT) Display
When the [AUTO OPN MODE] key is pressed at the “MAIN MENU” display,
the following display appears on the screen.
Automatic operation of the machine can only be started while this dis-
play is active.
Note: The -marked items are optional.
Fig. 3.1
*1 Current Date and Time
*2 Current Program Name and Comment #1
*3 Step and Feeder Nos. of Placed Component
Indicated are the placement step Nos. for the heads on Beams A and B.
“U01” represents the U-No. (block No.) of the current pattern program
(program being executed).
“O0001” is a repetitive pattern No. and appears only when repetitive pat-
terns are set.
*4 Current Operation Mode
(RUN, PAUSE, STOP, or WAIT)
*5 [MAIN MENU] Key
When this key is pressed, the “MAIN MENU” display appears on the
screen.
0103-003 3-3 Tg0246-PM-OP
*1
*4
*14
*3
*11
*9
*10
*8
*7
*6
*5
*2
*12
*13
2. AUTO OPN MODE (PLACEMENT) Display
DEVICE TESTDEVICE TEST
(PLACEMENT)
(
PASSAGE
)
9910-001 3-4 Tg0246-PM-OP
*6 Normally the key is labeled as follows.
CAUTION
Do not perform automatic operation when the
key is labeled as “DEVICE TEST (PLACE-
MENT)” or “DEVICE TEST (PASSAGE)”.
Normal automatic operation cannot be per-
formed because test mode data is set.
“(PLACEMENT)” or “(PASSAGE)” simply shows the status of the vacuum
pump.
(PLACEMENT) : Vacuum Pump ON
(PASSAGE) : Vacuum Pump OFF
*7 The number of produced P.C.B.’s is counted for both single- and multi-
unit P.C.B.’s when specified in the pattern program data.
Single-Unit P.C.B. : Normally the counter counts up in increments of
one P.C.B. in the pattern program data and the re-
petitive pattern program data.
Multi-Unit P.C.B. : The counter counts up the number of unit P.C.B.’s
where components are actually placed.
Example:
*8 This section displays the time required to finish one P.C.B. excluding the
P.C.B. in the middle of process.
This is the total time from the P.C.B. transfer start until the X/Y beam is
zeroed after the completion of the last component placement.
*9 [CLEAR THE P.C.B. COUNTER] Key
This key is used to clear the P.C.B. counter *7 to “0” (zero).
*10 This section displays information on machine status.
*11 [AUTO OPN SUB-MENU] Key
This key is used to call the operation and function menus required for
automatic operation.
AUTO OPN MODE
(
PLACEMENT
)
AUTO OPN MODE
(
PASSAGE
)
NG
NG
The counter reads the following when the
P.C.B. described on the left is processed.
Single-Unit P.C.B. : +1
Multi-Unit P.C.B. : +12 - 2 (defective
P.C.B.’s) = +10
2. AUTO OPN MODE (PLACEMENT) Display
*12 [SCREENS] Key
When this key is pressed, the information in “ORIGIN MONITOR” *14
changes.
*13 [LOCK] and [UNLOCK]
Each pressing of this key locks and unlocks the indication on the box
shown as *13.
*14 Monitor Information under Automatic Operation
Every time the [SCREENS] key *12 is pressed, the information in the
monitor box changes.
• ORIGIN MONITOR
Devices located at their origins are marked
with “”.
Note: The -marked items are optional.
• DEVICE TEST
Displayed in the monitor box are param-
eters set as test mode data.
(Not used in normal cases)
Notes:
(a) As long as each parameter is set
to establish the placement mode,
this display does not appear on the
screen, regardless of the param-
eter (either “ENABLE” or “DIS-
ABLE”) set in the “DRY CYCLE
MODE” data box at the “TEST
MODE” display.
(b) The -marked items are optional.
• INP./OUT.MACH. SIGNAL INFO.
Signal exchanges (ON/OFF status) be-
tween the main and input or output ma-
chines are displayed at real time.
When a signal is ON, the background color
of the signal indicator section turns green.
This function can be used to check the sig-
nal system at the system connection.
0103-003 3-5 Tg0246-PM-OP
[SCREENS] Key
[SCREENS] Key
[SCREENS] Key