1OM-1064-002.pdf - 第5页
Tg0246-PM-OP This instruction manual consists of six books (V olumes 1 to 5 and COMPONENT LIBRAR Y). Before operating the machine, please read these books carefully to ensure correct operation. • The contents of V olumes…
Tg0246-PM-OP
0304-003 2
Before Use
4. Inquiry
• For detailed information about any transfer, resale, modification of the
machine or the instruction manual, contact our marketing department or
agency.
5. Training
• For training for this machine, contact our marketing department or agency.
6. About Safety Precaution Labels
• The warning indications are classified into the following three types, accord-
ing to the degree of danger. Please be sure of the precautions in the warning
instructions and take due care for safety.
• Identifying Alert Icons
: This symbol mark represents danger or prompts warning.
: This symbol mark represents prohibited operations.
: This symbol mark represents forced operations or instructions.
7. The contents of this manual are subject to change without prior
notice.
This indicates a potentially hazardous situation
which, if not avoided, may result in injury or physi-
cal damage.
CAUTION
DANGER
This indicates an imminently hazardous situation
which, if not avoided, will result in death or seri-
ous injury.
This indicates a potentially hazardous situation
which, if not avoided, could result in death or seri-
ous injury.
WARNING
Tg0246-PM-OP
This instruction manual consists of six books (Volumes 1 to 5 and COMPONENT
LIBRARY).
Before operating the machine, please read these books carefully to ensure correct
operation.
• The contents of Volumes 1 to 5 are as follows.
Volume 1 : Operation
This volume covers the scope of the machine, the preparatory and
ending procedures of automatic operation.
Volume 2 : Programming
This volume discusses steps in creating, entering and editing various
kinds of data (pattern program data, etc.) required to activate the
machine.
Volume 3 : Troubleshooting
This volume describes the causes of various troubles and recovery
methods.
Volume 4 : Maintenance
This volume covers the steps required for daily maintenance.
Volume 5 : Material
This volume covers the air piping and electrical circuit diagrams, etc.
• The contents of COMPONENT LIBRARY are as follows.
COMPONENT LIBRARY
Creation of Component Library Data, etc.
0004-002 3
How This Manual is Organized
Contents
Page
0103-002 4 Tg0246-PM-OP
Before Use ................................................................................................... 1
How This Manual is Organized .................................................................... 3
Contents ....................................................................................................... 4
1. Safety Precaution “Safety Requirements” ............................................... 9
1.1 Caution of Pre-Installation .................................................................. 9
1.2 Precautions before Operation .......................................................... 11
1.3 Precautions during Operation .......................................................... 12
1.4 Precautions in Maintenance ............................................................. 14
1.5 Other Precautions ............................................................................ 15
2. Warning Labels ...................................................................................... 16
2.1 Warning Label Locations .................................................................. 16
2.2 Warning Label Description ............................................................... 19
3. Safety Switches...................................................................................... 21
3.1 [EMERGENCY STOP] Buttons ........................................................ 21
3.2 Maintenance Cover Check Switches ................................................ 22
3.3 Supply Cover and Safety Bar Check Switches ................................ 23
4. Machine Protection Sensors .................................................................. 24
4.1 Lifted Feeder Detection Sensors ...................................................... 24
4.2 Lifted Nozzle Detection Sensors ...................................................... 25
4.3 Beam Approach Detection Sensor ................................................... 25
4.4 Stationary Position Stopper Detection Sensors ............................... 25
4.5 Excessively Insterted Nozzle Detection Sensors ............................. 26
4.6 Nozzle Up/Down Axis Lever Detection Sensors .............................. 27
4.7 Maintenance Opening Detection Sensors ........................................ 28
Section 1 Scope ................................................................................. 1- 1
1. Scope of Machine ............................................................................ 1- 2
2. Specifications .................................................................................. 1- 3
3. Functions ......................................................................................... 1-21
3.1 Component Recognition Function ............................................. 1-21
3.2 P.E.C. Recognition Function ...................................................... 1-21
3.3 Equivalent Repetitive Pattern Function ..................................... 1-22
3.4 Function for Multi-Model Repetitive Patterns
(Application for Un) ................................................................... 1-22
3.5 Priority Sorting Function ............................................................ 1-23
3.6 Component Library .................................................................... 1-23
3.7 Automatic Feeder Axis Adjustment Function............................. 1-23
3.8 Automatic Recovery Function (Reserved Data) ........................ 1-23
3.9 Alternate Mode .......................................................................... 1-24
3.10 One-Touch Jump Function (Jump to Substitute
AUTO OPN. MODE <PLACEMENT> Display)........................ 1-24
3.11 Device Information ................................................................... 1-25
3.12 Simplified Packaging Direction Change Function
(Editing of Component Carriage Data) .................................... 1-25
3.13 Conveyor Width Automatic Adjustment Function .................... 1-25