1OM-1064-002.pdf - 第181页
3. AUTO OPN SUB-MENU Display T able 3.1- 2 9910-001 3-12 Tg0246-PM-OP Footnot e THE NOZZLE TYPE DATA IS TOO LARGE FOR T HE AVAILABLE MEMORY SPACE. CAN NOT SAV E DATA, BECAUS E TEACH RESULT DATA WAS ERROR. CANNOT PE RFORM…
3. AUTO OPN SUB-MENU Display
*15 [INDIVIDUAL FDR. ENABLE/DISABLE] key
This key is used to confirm the alternate feeder change or to instruct the compo
nent supply feeder operation completion. Refer to Section 3, Alternate Function
Valid/Invalid Setting for details.
Footnote
*16 Prohibited operation messages are displayed.
Table 3.1-
1
0103-003 3-11 Tg0246-PM-OP
Footnote
CANNOT SELECT MENU IN [PAUSE] MODE.
CANNOT MODIFY DATA IN [PAUSE] MODE.
CANNOT SAVE DATA IN [PAUSE] MODE.
CANNOT SELECT MENU IN [RUN] OR [WAIT] MODE.
CANNOT MODIFY DATA IN [RUN] OR [WAIT] MODE.
CANNOT SAVE DATA IN [RUN] OR [WAIT] MODE.
CANNOT SELECT MENU IN [RUN], [WAIT], OR [PAUSE] MODE.
CANNOT MODIFY DATA IN [RUN], [WAIT], OR [PAUSE] MODE.
CANNOT SAVE DATA IN [RUN], [WAIT], OR [PAUSE] MODE.
CANNOT SAVE CURRENT PROGRAM IN [RUN], [WAIT], OR [PAUSE] MODE.
CANNOT PERFORM OPERATION.
CANNOT SELECT MENU DURING MACHINE OPERATION.
CANNOT SELECT MENU DURING DATA COMMUNICATION WITH EXTERNAL DEVICE.
RECOGNITION DEVICE NOT READY.
SELECT CORRECT DATA.
CURRENT PATTERN PROGRAM NOT SPECIFIED.
BROKEN PATTERN PROGRAM DATA.
“PASSED” MODE SET IN OPERATION DATA.
CANNOT PERFORM OPERATION IN “PASSED” MODE.
OPERATION DENIED BY LOGIN TYPE.
PLEASE PRESS THE [RESET] BUTTON TOGETHER.
CANNOT SELECT MENU EXCEPT [PAUSE] MODE.
CANNOT SELECT MENU DURING TRAY OPERATION.
NO SAVING AREA IN FD.
CANNOT FIND THE FILE IN FD.
WRONG FLOPPY DISK.
CANNOT BE SAVED ON A WRITE-PROTECTED FD.
CANNOT READ THE DATA.
THE PATTERN PROGRAM DATA IS TOO LARGE FOR THE AVAILABLE MEMORY SPACE.
PLEASE INPUT CORRECT FDR#.
CANNOT MODIFY DATA DURING ATTACHED NOZZLE WITH HEAD.
CAN NOT OPERATION, BECAUSE DOES NOT FRONT PANEL.
CAN NOT OPERATION AT COMBINATION OF DESIGNATED HEAD AND FEEDER.
CAN NOT OPERATION, BECAUSE DOES NOT REAR PANEL.
ZERO BACKUP UP/DOWN AXIS (BPC-AXIS).
P.C.B. ON P-CONVEYOR WAS NOT DETECTED.
TROUBLE OCCURRED IN INTERNAL PROCESSING.
PLEASE INPUT CORRECT COMPONENT THICKNESS.
PLEASE INPUT NOZZLE TYPE.
CANNOT SELECT MENU DURING TEACHING RESULT DATA NOT EXIST.
CANNOT TEACH START MENU, ILLEGAL PLACEMENT POSITION.
CAN NOT OPERATION AT COMBINATION OF DESIGNATED CARRIER TYPE AND FEEDER.
PLEASE COLLECT COMPONENT.
CANNOT PERFORM OPERATION IN HEAD SKIP OR BEAM LOCK.
DISABLE OVER-WRITE MODE
3. AUTO OPN SUB-MENU Display
Table 3.1-2
9910-001 3-12 Tg0246-PM-OP
Footnote
THE NOZZLE TYPE DATA IS TOO LARGE FOR THE AVAILABLE MEMORY SPACE.
CAN NOT SAVE DATA, BECAUSE TEACH RESULT DATA WAS ERROR.
CANNOT PERFORM OPERATION IN BEAM-B HEADS.
NOT COMPLETE SAVE FD PREVIOUS DATA.
CANNOT PERFORM OPERATION IN DRAWING PALLET.
THE VALUE OF TRAY HEIGHT IS OUT OF RANGE.
CANNOT SELECT MENU DURING P.E.C. RECOG. NOT COMPLETED.
CANNOT SELECT MENU DURING UNIT P.C.B. B.B.R. NOT COMPLETED.
CANNOT SELECT MENU DURING PATTERN OFFSET TEACH. (TEMPORARY ENTRY
MODE)
CANNOT SELECT MENU DURING PLACEMENT POSITION TEACH. (TEMPORARY
ENTRY MODE)
CANNOT SELECT MENU DURING 1POINT MODE TEACH.
CANNOT SELECT MENU DURING 1POINT TEACH STATUS. (NOT COMPLETE)
CANNOT SELECT MENU. PLACEMENT POSITION TEACH IS NOT TEMPORARY ENTRY
MODE.
PLACEMENT POSITION TEACH IS NOT SET ILLEGAL DATA.
NOT AVAILABLE PLACEMENT PATTERN PROGRAM STEP.
PLEASE RELEASE A PREPARATIONS COMPLETION OF BEAM-A.
PLEASE RELEASE A PREPARATIONS COMPLETION OF BEAM-B.
CAN NOT PERFORM OPE. BANK CRG. CART IS NOT LOC. AT CONNECT OR
DISCONNECT POS.
OPEN THE COMPONENT SUPPLY COVER [A].
OPEN THE COMPONENT SUPPLY COVER [B].
OPERATION DENIED BY THIS SCREEN.
CANNOT SELECT MENU IN [WAIT] MODE AS PLACEMENT MODE.
SET THE SAFETY BAR [A].
SET THE SAFETY BAR [B].
TURN ON THE [POWER ON] BUTTON.
CIRCUIT PROTECTOR FOR FEEDER [A] (BACK SIDE) IS ACTIVE.
CIRCUIT PROTECTOR FOR FEEDER [B] (FRONT SIDE) IS ACTIVE.
YA-AXIS LOCATE STOPPER FORWARD LIMIT NOT DETECTED.
YB-AXIS LOCATE STOPPER FORWARD LIMIT NOT DETECTED.
ZERO YA-AXIS.
ZERO YB-AXIS.
ZERO TFA1-AXIS.
ZERO TFB1-AXIS.
CANNOT SELECT MENU DURING BANK CARRIAGE CART DISCONNECT.
CAN NOT OPERATION, BECAUSE HEAD IS BYPASSED.
CAN NOT OPERATION, BECAUSE CAMERA IS BYPASSED.
CAN NOT OPERATION, BECAUSE USEFUL NOZZLE IS SHORTAGE.
CAN NOT SAVE DATA, PLEASE USE ANOTHER FD.
CAN NOT OPERATION, BECAUSE SIF CHECK MODE.
4. SEMI-AUTOMATIC OPERATION
*4*9*12*11*8
*6
*7
*3
*2
*5
*1
*10
4. SEMI-AUTOMATIC OPERATION
• This function enables special start-up operations such as resetting and con-
tinuous starting of semi-automatic operation from the P.C.B. in the middle
of process after power is turned off and starting of placement operation
from the middle of steps after system clear.
• Components can be placed on the positioned P.C.B. from the desired step
No. or only one component in the desired step No. can be placed on the
P.C.B.
4.1 Normal Step Designation (Without Non-Placement
Steps)
When the [SEMI-AUTOMATIC OPERATION] key is pressed at the “AUTO
OPN SUB-MENU” display, the following display appears on the screen.
Note: This key can be selected only when the machine is in the “STOP” mode.
Fig. 3.3
*1 [BEAM-A STEP] and [BEAM-B STEP] keys
Specify the beam to be operated.
When the selected key illuminates in blue, the corresponding beam can be
operated.
If not, the beam cannot be operated.
Every time the key is pressed, the key turns blue or not.
0004-002 3-13 Tg0246-PM-OP