1OM-1064-002.pdf - 第9页

Contents Page 9910-001 7 Tg0246-PM-OP 7.4 Possible Operations during Automatic Operation ..................... 2-66 7.5 Emergency Stop ........................................................................ 2-67 7.5.1 C…

100%1 / 244
Contents
Page
9910-001 6 Tg0246-PM-OP
5. Preparation and Confirmation before Operation ............................. 2-30
5.1 Preparation of Pattern Program ................................................ 2-30
5.1.1 Preparation of Component Library ...................................... 2-30
5.1.2 Creation of Pattern Program for Production Model ............. 2-31
5.1.3 Registration (Storage in Memory) of Pattern Program for
Production Model .................................................................... 2-31
5.2 Program Change Operation ...................................................... 2-33
5.2.1 Selection of Current Pattern Program (Program Change) .. 2-33
5.2.2 Adjustment of P.C.B. Positioning Section ............................ 2-36
5.2.2.1 Adjustment of Conveyor Width ...................................... 2-36
5.2.2.2 Setting Procedure of P.C.B. Support Pins ..................... 2-37
5.2.3 Preparation of Nozzle Stocker Section ................................ 2-41
5.2.4 Preparation of Feeders ........................................................ 2-42
5.2.5 Feeder (B) Offset ................................................................. 2-43
5.3 Pattern Program Checking for Production Model ...................... 2-47
5.3.1 Setting and Checking of P.C.B. Recognition ....................... 2-47
5.3.2 Confirmation of Placement Position .................................... 2-47
5.3.3 Confirmation of Components ............................................... 2-48
5.3.4 Placement Verification ......................................................... 2-48
5.4 Setting of Operation Mode......................................................... 2-48
6. Starting, Emergency Stop, and Temporary Stop
(Pause) Operations for Automatic Operation (“PLACE” Mode) ....... 2-49
6.1 General Start Procedure............................................................ 2-49
6.2 Temporary Stop Procedure........................................................ 2-51
6.3 Start Procedure from “PAUSE” Mode ........................................ 2-51
6.4 Component Supply during Automatic Operation ....................... 2-52
6.4.1 Tape Feeders....................................................................... 2-52
6.4.2 Vibratory Stick Feeders ....................................................... 2-53
6.4.3 Multi-Layer Tray Feeders (Option) ...................................... 2-54
6.5 Operational Displays during Automatic Operation .................... 2-56
6.6 Interruption of Automatic Operation .......................................... 2-60
6.6.1 How to Interrupt the Automatic Operation ........................... 2-60
6.6.2 Function of [SYS CLR] Button ............................................. 2-60
6.7 Emergency Stop ........................................................................ 2-62
6.7.1 Cause and Symptom of Emergency Stop ........................... 2-62
6.7.2 Reset and Start Procedure from Emergency Stop .............. 2-62
6.8 Stop Operation .......................................................................... 2-63
6.8.1 General Stop Procedure ...................................................... 2-63
6.8.2 Automatic Stop Procedure................................................... 2-63
6.8.3 Emergency Stop Procedure ................................................ 2-63
7. Starting, Emergency Stop, and Temporary Stop (Pause)
Operations for Automatic Operation (“PASS” Mode) ....................... 2-64
7.1 Usage ........................................................................................ 2-64
7.2 Start Procedure ......................................................................... 2-64
7.3 Stop Procedure .......................................................................... 2-66
7.3.1 General Stop Procedure ...................................................... 2-66
7.3.2 Automatic Stop Procedure................................................... 2-66
7.3.3 Emergency Stop Procedure ................................................ 2-66
Contents
Page
9910-001 7 Tg0246-PM-OP
7.4 Possible Operations during Automatic Operation ..................... 2-66
7.5 Emergency Stop ........................................................................ 2-67
7.5.1 Cause and Symptom of Emergency Stop ........................... 2-67
7.5.2 Reset and Start Procedure from Emergency Stop .............. 2-68
8. Shut-Down Operation (End of Production) ...................................... 2-69
Section 3 Automatic Operation Menus ........................................ 3- 1
1. Hierarchical Structure of Automatic Operation Displays ................. 3- 2
2. AUTO OPN MODE (PLACEMENT) Display .................................... 3- 3
3. AUTO OPN SUB-MENU Display ..................................................... 3- 7
4. SEMI-AUTOMATIC OPERATION ................................................... 3-13
4.1 Normal Step Designation (Without Non-Placement Steps) ....... 3-13
4.2 Selection of WARM or COLD Start Operation ........................... 3-16
4.3 Warm Start ................................................................................ 3-17
5. Operation Mode ............................................................................... 3-19
5.1 AUTOMATIC FEEDER AXIS ADJUSTMENT MODE Display ... 3-20
5.2 OVERALL TACT-TIME REDUCTION Display ........................... 3-21
5.3 RECOG MONITOR DISPLAY MODE Display ........................... 3-23
5.4 P.E.C. MANUAL ALIGNMENT MODE Display .......................... 3-25
5.5 ALTERNATE MODE Display ..................................................... 3-26
5.6 COMPONENT MISSING CHECK MODE Display ..................... 3-31
6. RECOVERY OPN. TEACHING OPN. Display ................................ 3-32
6.1 PATTERN PROGRAM EDIT Display ........................................ 3-33
6.2 COMPONENT LIBRARY Display .............................................. 3-34
6.3 COMP. CARRIAGE DATA EDIT Display
(Simplified Packaging Direction Change Function)................... 3-35
6.4 FEEDER (B) OFFSET Display .................................................. 3-41
7. Tray Pick-Up Matrix (Option) ........................................................... 3-42
Section 4 Manual Mode Menus ...................................................... 4- 1
1. Hierarchical Structure of Manual Mode Displays ............................ 4- 2
2. MANUAL MODE Display ................................................................. 4- 3
3. Program Change ............................................................................. 4- 5
4. Product Change .............................................................................. 4- 6
4.1 Selection of Set-Up Menus and Overall Set-Up Operation ....... 4- 6
4.2 Manual Set-Up at Each Display (Display for Each Device) ....... 4- 8
4.3 Overall Automatic Set-Up Function Interlinked with
Program Change ....................................................................... 4-10
5. Zeroing Operation ........................................................................... 4-11
6. Manual Subsystem Operation ......................................................... 4-13
7. Manual Axis Operation .................................................................... 4-14
8. Manual Transfer Operation ............................................................. 4-18
9. Manual Nozzle Change Operation .................................................. 4-22
9.1 Procedure for Nozzle Stocker Opening/Closing Operation ....... 4-22
9.2 Procedure for Nozzle Attachment.............................................. 4-22
9.3 Procedure for Nozzle Storage ................................................... 4-23
Contents
Page
9.4 Procedure for Nozzle Batch Storage ......................................... 4-23
9.5 Procedure for Continuous Operation
(Test on Nozzle Attachment and Storage Operations).............. 4-23
10. P.C.B. Support Pins Set-Up Mode ................................................. 4-26
9910-001 8 Tg0246-PM-OP