Administrator’s Guide(CP45FV) Eng.pdf - 第282页

Samsung Component Placer CP45FV Administrator ’ Guide guide). <Position X, Y – Pre Dump> edit box     Set the position on which the head block stops before dumping. <Release Z Height> edit box Set the Z a…

System Setup

16-15

Head5: Selects Head5.

Head6: Selects Head6.

Beam: Selects Beam.

<Move> button 



Moves the head assembly by rotating the shafts of the X, Y and Z-axes driving

motors using the device selected from the <Device> combo box. At this time, the edit

box corresponding to the position to move to must be clicked on with a mouse.

<Get> button

Reads in the XY and Z axis of the device selected in <Device>. At this time, the edit

box corresponding to the position to be read must be clicked on with a mouse.

<Update> button

Transmits the set data to the machine and closes the dialog box.

<Cancel> button

Ignores the set data and closes the dialog box.

16.6. Dump [F7]

Sets the data on the dump box where the picked up components are dumped.

When this button is clicked on, the following dialog box is displayed.

Figure 16-8. “Sys. Setup : Dump Box” dialog box





<System Default Dumpbox> group

Set the data on the system dump box provided by the System as a default. 2 system

dump boxes are installed on the conveyor guide located close to the front of the

machine as a default.

<Position X, Y – Front Left(1)> edit box

Set the position of the system dump box 1(Located on the left of the conveyor

Samsung Component Placer CP45FV Administrator’ Guide

guide).

<Position X, Y – Pre Dump> edit box 





Set the position on which the head block stops before dumping.

<Release Z Height> edit box

Set the Z axis height of the head at the time of dumping.

<Part Dump Conveyor> group

The position of the part dump conveyor is set to default. If the position of the part

dump conveyor is needed to change, check <Use> check box and teach its new

position.

<User Define Dumpbox> group

Set the data on the user dump box installed by the user. The maximum number of

dump boxes that can be set by the user is 5.

The User Dump Box, which is installed by the user at his/her discretion, is used when

dumping components at the User Dump position in case the components to be

dumped are expensive or need to be classified or when a component error occurs.

Memo

Once the User Dump Box is setup, if the dump item of the feeder for the corresponding

components is not set as “User Dump” in the Feeder dialog box, the front left position is

set as the default value.

The setup procedure of the User Dump Box is as follows;

1. Select the <Use> check box and move the head to the place where the user dump

box is installed using the teaching box.

2. Select the “Move Cam” in the <Device> combo box, and align the center of the

user dump box on the cross hair center of the Move Camera (Fiducial Camera)

shown on the vision monitor accurately using the teaching box.

3. Click the <Get> button to enter the current coordinate.

4. Click the <Update> button to reflect the changed value.

After updating, select the dump item for the feeder supplying the component that

uses the user dump as “User Dump”.

<Grid - No> column 



Displays the user dump box number.

<Grid - Use> column

Set whether to use the corresponding user dump box or not.

<Grid - X> column

Set the X position of the corresponding user dump box.

<Grid - Y> column

Set the Y position of the corresponding user dump box.

<Grid – Release Z> column

Set the Z axis height of the head at the time of dumping to the corresponding user

dump box.

16-16

System Setup

16-17



<Device> combo box

Selects the corresponding device to move the head assembly by rotating the driving

shafts of the X, Y and Z-axes motors, move or rotate the spindle or obtain the current

coordinate of the device to be selected. Available devices are as follows;

Move Cam: Selects Teaching Camera.

Head1: Selects Head1.

Head2: Selects Head2.

Head3: Selects Head3.

Head4: Selects Head4.