Administrator’s Guide(CP45FV) Eng.pdf - 第283页
System Setup 16-17 <Device> combo box Selects the corresponding device to move th e head assembly by rotating the driving shafts of the X, Y and Z-ax es motors, move or rotate the spindle or obtain the cu…
Samsung Component Placer CP45FV Administrator’ Guide
guide).
<Position X, Y – Pre Dump> edit box
Set the position on which the head block stops before dumping.
<Release Z Height> edit box
Set the Z axis height of the head at the time of dumping.
<Part Dump Conveyor> group
The position of the part dump conveyor is set to default. If the position of the part
dump conveyor is needed to change, check <Use> check box and teach its new
position.
<User Define Dumpbox> group
Set the data on the user dump box installed by the user. The maximum number of
dump boxes that can be set by the user is 5.
The User Dump Box, which is installed by the user at his/her discretion, is used when
dumping components at the User Dump position in case the components to be
dumped are expensive or need to be classified or when a component error occurs.
Memo
Once the User Dump Box is setup, if the dump item of the feeder for the corresponding
components is not set as “User Dump” in the Feeder dialog box, the front left position is
set as the default value.
The setup procedure of the User Dump Box is as follows;
1. Select the <Use> check box and move the head to the place where the user dump
box is installed using the teaching box.
2. Select the “Move Cam” in the <Device> combo box, and align the center of the
user dump box on the cross hair center of the Move Camera (Fiducial Camera)
shown on the vision monitor accurately using the teaching box.
3. Click the <Get> button to enter the current coordinate.
4. Click the <Update> button to reflect the changed value.
After updating, select the dump item for the feeder supplying the component that
uses the user dump as “User Dump”.
<Grid - No> column
Displays the user dump box number.
<Grid - Use> column
Set whether to use the corresponding user dump box or not.
<Grid - X> column
Set the X position of the corresponding user dump box.
<Grid - Y> column
Set the Y position of the corresponding user dump box.
<Grid – Release Z> column
Set the Z axis height of the head at the time of dumping to the corresponding user
dump box.
16-16
System Setup
16-17
<Device> combo box
Selects the corresponding device to move the head assembly by rotating the driving
shafts of the X, Y and Z-axes motors, move or rotate the spindle or obtain the current
coordinate of the device to be selected. Available devices are as follows;
Move Cam: Selects Teaching Camera.
Head1: Selects Head1.
Head2: Selects Head2.
Head3: Selects Head3.
Head4: Selects Head4.
Head5: Selects Head5.
Head6: Selects Head6.
Beam: Selects Beam.
<Move> button
Moves the head assembly by rotating the shafts of the X, Y and Z-axes driving
motors using the device selected from the <Device> combo box. At this time, the edit
box corresponding to the position to move to must be clicked on with a mouse.
<Get> button
Reads in the current position of the XY and Z axes of the device selected in <Device>.
At this time, the edit box corresponding to the position to be read must be clicked on
with a mouse.
<Update> button
Transmits the set data to the machine and closes the dialog box.
<Cancel> button
Ignores the set data and closes the dialog box.
Samsung Component Placer CP45FV Administrator’ Guide
16.7. Pref. [F9]
Sets various options needed for machine operation.
When this button is clicked on, the following dialog box is displayed.
Figure 16-9. “Sys. Setup : System Preference - General” dialog box
<General> tab dialog
Sets various options used in the MMI program.
<Skip the erroneous Component> check box
If this button is checked, when a component fails to be picked up during
placement, skips the corresponding component, and place it again after all the
rest placement operation is completed.
<No Auto Link> check box
Tape
If selected, the auto link function will not be used for the tape feeder..
Stick
If selected, the auto link function will not be used for the stick feeder.
Tray
If selected, the auto link function will not be used for the tray feeder.
<Buzzer On at error State> check box
If this button is checked, when an error occurs while a function is being
performed in the machine, a buzzer rings.
<Keep Production Information> check box
When this button is checked, manages the production management information.
<Use fast pallet change function> check box
When placement is done with components from more than one pallet, after a
component is picked up from a pallet, the next pallet waits in the working
16-18