N7201A618E00_0309.pdf - 第101页

NPM–W 2 EJM7DE-MB-02 -1T-00 Threshold set err (VLC) Comm. status err (VLC) Sensor abnormality (VLC) Solutions to errors Error Code Error Message Cause Inspection and Solution Any of the following causes is likely: 1) Cam…

NPM–W2 EJM7DE-MB-02-1T-00

Stamp Parts Drop Error

Stamp Time Over Error

Stamp Empty Error

Nozzle Error Rate Stop

Error

Message

Troubleshooting

2-1-3

Single stop error 16

Error Code

Error Message

Cause Inspection and Solution

Pickup errors and/or

recognition errors have

occurred beyond the bad

nozzle error rate set in action

parameters.

(Single stop error occurred.)

Check the condition of the nozzle

and clean it if necessary.

40396

Transcript material has run

out.

(Single stop error occurred.)

Supply the transcript material.

40397

Transcript time was

exceeded.

(Single stop error occurred.)

Supply the transcript material.

40398

Component may have

dropped in the transcript unit.

(Single stop error occurred.)

Check the transcript unit and

remove any component.

40399

2-1-3-30

NPM–W2 EJM7DE-MB-02-1T-00

Threshold set err

(VLC)

Comm. status err

(VLC)

Sensor abnormality

(VLC)

Solutions to errors

Error Code

Error Message

Cause Inspection and Solution

Any of the following causes

is likely:

1) Camera is blocked entirely

or partly.

2) Optical axis is displaced.

3) Failure of vertical line

camera detected.

(Single stop error occurred.)

Take measures shown with the

same number as that of the cause.

1) Since the sensor is blocked,

remove any foreign body. Wipe

away any dirt from the lens if it is

dirty. If there is no foreign body,

check the connection of connector.

2) Adjust the optical axis of the

sensor.

3) Check the situation of the error

occurred and error message, and

contact PFSC.

40400

Communication status error

detected in issuing command.

(Single stop error occurred.)

Check the situation of the error

occurred and error message, and

contact PFSC.

40401

Nozzle height offset is

beyond the threshold value.

Pre-scanning setting of the

vertical line camera could not

be made.

(Single stop error occurred.)

The offset value of the nozzle height

detection is not correct. Calibrate

the origin offset Z-axis and vertical

line camera.

40402

2-1-3-31

NPM–W2 EJM7DE-MB-02-1T-00

Nzl Point Abnormal Error

Nzl Height Range Ov

(VLC)

Nzl Height Det Err

(VLC)

Error

Message

Troubleshooting

2-1-3

Single stop error 17

Error Code

Error Message

Cause Inspection and Solution

Any of the following causes

is likely:

1) Measured nozzles and

measurement result

nozzles do not agree.

2) Measurement result is out

of output value.

(Single stop error occurred.)

Take measures shown with the

same number as that of the cause.

1) Check the mounting condition of

the nozzle.

2) Make sure that there is no foreign

body on the lens of the vertical line

camera and diagonal line on the

emitter and detector sides of the

laser. Calibrate the origin offset Z-

axis and vertical line camera.

40403

Any of the following causes

is likely:

1) Difference between nozzle

detection result and nozzle

length exceeded ±0.050

mm.

2) Nozzle recognition height

and optical axis of the

vertical line camera are

displaced.

(Single stop error occurred.)

Take measures shown with the

same number as that of the cause.

1) Check the nozzle length.

2) Calibrate the origin offset Z-axis

and vertical line camera.

40404

Tip of the nozzle is not planar.

(Single stop error occurred.)

Check the tip of the nozzle and

clean it. Replace the faulty nozzle.

40405

2-1-3-32