N7201A618E00_0309.pdf - 第76页

NPM–W 2 EJM7DE-MB-02 -1T-00 Splicing Length Sto p Cover Open PCB Position Error Error Message Troubleshooting 2-1-3 Sing le stop er r o r 4 Error Code Error Message Cause Inspection and Solution PCB is removed or is not …

NPM–W2 EJM7DE-MB-02-1T-00

Conveyor Width Adj. Err

PCB Transfer Error

PCB Recognition Error

Solutions to errors

Error Code

Error Message

Cause Inspection and Solution

Any of the following causes

is likely:

1) Recognition mark is out of

camera's view.

2) Recognition error

occurred due to dirt on PCB.

3) PCB recognition

coordinates are incorrect.

(Single stop error occurred.)

Take measures shown with the

same number as that of the cause.

1) Using the inching function, move

the camera to the recognition mark

position and press the Re-

recognize button.

2) After cleaning the recognition

camera and PCB, press the Re-

recognize button. If the recognition

error occurs again, move the

camera to the recognition mark

position with the Pass button or

inching function and press the

Manual set button. [Pass]: Pass

the PCB.[Manual set]: Save the

inching amount as the offset.

3) Choose [Production data] -

[Correct] - [PCB] - [PCB recog.]

and enter the correct PCB

recognition coordinates.

40313

PCB failed to be transferred

properly.

(Single stop error occurred.)

Check inside the machine and

remove the PCB.

40314

Width adjustment is disabled

because of the PCB on the

conveyor.

(Single stop error occurred.)

Remove the PCB.

40315

2-1-3-5

NPM–W2 EJM7DE-MB-02-1T-00

Splicing Length Stop

Cover Open

PCB Position Error

Error

Message

Troubleshooting

2-1-3

Single stop error 4

Error Code

Error Message

Cause Inspection and Solution

PCB is removed or is not

placed at the correct position.

(Single stop error occurred.)

1) Set the PCB in position.

2) If the PCB is removed, press the

[PCB Remove] button.

40316

Safety cover is open.

(Single stop error occurred.)

Take measures in the following

order.

1) Close the safety cover if opened.

2) If the error persists even after the

safety cover is closed, the safety

switch may be at fault.Contact

PFSC.

40317

Tape is getting low.

(Single stop error occurred.)

Perform tape splicing.

40318

2-1-3-6

NPM–W2 EJM7DE-MB-02-1T-00

Pick-up Height Measure

Error

No Splicing Check Warn.

No Splicing Check

Solutions to errors

Error Code

Error Message

Cause Inspection and Solution

Any of the following causes

is likely:

1) Splicing work not

performed.

2) Spliced part of the tape

has been recognized by

mistake.

(Single stop error occurred.)

Take measures shown with the

same number as that of the cause.

1) Perform splicing work properly.

Make sure the reel is properly

installed and check the joint

detection sensor. Then, press the

Supply Complete button.

2) Cancel the joint detection.

40319

Any of the following causes

is likely:

1) Splicing work not

performed.

2) Spliced part of the tape

has been recognized by

mistake.

(Single stop error occurred.)

Take measures shown with the

same number as that of the cause.

1) Perform splicing work properly.

Make sure the reel is properly

installed and check the joint

detection sensor. Then, press the

Supply Complete button.

2) Cancel the joint detection.

40320

Feeder or tray not set from

which the component is

picked up.

(Single stop error occurred.)

Make sure that the feeder or pallet is

properly set and the nozzle is

properly set on the head.

40321

2-1-3-7