N7201A618E00_0309.pdf - 第198页

NPM–W 2 EJM7DE-MB-02 -1T-00 Emergency Stop Deceleratio n Error Error Deceleration Error Acceleratio n Command Error Speed Command Err or Error Message Troubleshooting 2-1-4 Emer genc y stop er r or s 15 Error Code Error …

100%1 / 338
NPM–W2 EJM7DE-MB-02-1T-00
Data Set Command Not
Issued Error
Write EEPROM Error
Servo Ready Off
Completion Error Interrupt
Solutions to errors
Error Code
Error Message
Cause Inspection and Solution
Unwanted interrupt occurred
during positioning of X/Y
axes.
(Completion interrupt error
occurred)
1) Restart the machine.
2) If the error persists, contact PFSC.
1542
Axis movement failed
because it was attempted
without the communication
with the servo amplifier
established.
(Servo ready OFF error
occurred.)
Restart the machine.If the error
persists even after the machine is
restarted, contact PFSC.
1543
Wiring between the main
controller and servo amplifier
may be broken.
(Writing to EEPROM in servo
amplifier failed to finish
properly.)
Make sure the wiring between the
main controller and servo amplifier
is not broken.
1545
Improper procedure was
taken in software processing.
(Axis movement failed due to
incorrect data of the
applicable axis (mismatch of
data combination).)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1546
2-1-4-28
NPM–W2 EJM7DE-MB-02-1T-00
Emergency Stop
Deceleration Error
Error Deceleration Error
Acceleration Command
Error
Speed Command Error
Error
Message
Troubleshooting
2-1-4
Emergency stop errors
15
Error Code
Error Message
Cause Inspection and Solution
Improper procedure was
taken in software processing.
(Axis movement failed
because of zero set for the
axis speed.)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1550
Improper procedure was
taken in software processing.
(Axis movement failed
because of zero set for the
axis acceleration.)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1557
Improper procedure was
taken in software processing.
(Axis movement failed
because of zero set for the
axis deceleration for error
stop.)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1558
Improper procedure was
taken in software processing.
(Axis movement failed
because of zero set for the
axis deceleration for
emergency stop.)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1559
2-1-4-29
NPM–W2 EJM7DE-MB-02-1T-00
Action Command Error
Successive Action Setting
Error
Position Range Setting
Error
Axis Action Error
Solutions to errors
Error Code
Error Message
Cause Inspection and Solution
Improper procedure was
taken in software processing.
(Movement command issued
while the axis was moving.)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1561
Improper procedure was
taken in software processing.
(Minimum value set in the
position range is greater than
the maximum value.)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1562
Improper procedure was
taken in software processing.
(Incorrect parameter setting
values.)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1564
Improper procedure was
taken in software processing.
(Undefined command
issued.)
Close the error screen and restart
production. Then, check the
situation of the error occurred and
error message, and contact PFSC.
1566
2-1-4-30