N7201A618E00_0309.pdf - 第104页

NPM–W 2 EJM7DE-MB-02 -1T-00 Feeder Pull-out error Servo Switch Off Pick up error (VLC) Error Message Troubleshooting 2-1-3 Single stop er r or 18 Error Code Error Message Cause Inspection and Solution Any of the followin…

NPM–W2 EJM7DE-MB-02-1T-00

Shape of Parts err

(VLC)

Part Thick range ov

(VLC)

Part Thick det err

(VLC)

Solutions to errors

Error Code

Error Message

Cause Inspection and Solution

Any of the following causes

is likely:

1) Measured nozzles and

measurement result

nozzles do not agree.

Scanning status of

measured component

affects the scan of other

nozzles.

2) Measurement result is out

of effective range of output

value of the vertical line

camera.

(Single stop error occurred.)

Make sure the component is set

properly and correct values of the

component data (component

dimensions, etc.) are set.

40406

Component thickness

measurement result is

beyond the threshold value of

thickness tolerance.

(Single stop error occurred.)

Check the upper and lower limits of

the thickness tolerance in the

mounting condition data of

component data.

40407

Invalid component pickup

status.

(Single stop error occurred.)

Check the component data

(component dimensions, etc.).Check

the pickup condition.

40408

2-1-3-33

NPM–W2 EJM7DE-MB-02-1T-00

Feeder Pull-out error

Servo Switch Off

Pick up error

(VLC)

Error

Message

Troubleshooting

2-1-3

Single stop error 18

Error Code

Error Message

Cause Inspection and Solution

Any of the following causes

is likely:

1) Incorrect component data

height

2) Improper component feed.

3) Incorrect feeder position.

(Single stop error occurred.)

Take measures shown with the

same number as that of the cause.

1) Correct the component data.

2) Replace the tape feeder.

3) Choose [Production data] -

[Teach] - [Feeder] - [Pickup

position] and perform teaching of

the component pickup position.

40409

Servo switch turned OFF.

(Single stop error occurred.)

Take measures in the following

order.

1) Turn the servo switch clockwise

to turn it ON. (One position each at

front and rear)

2) If the error persists even after the

servo switch is tuned ON, the

switch may be broken.Contact

PFSC.

40410

Feeder was pulled out due to

a reason other than

component empty.

(Single stop error occurred.)

Set the feeder again.

40411

2-1-3-34

NPM–W2 EJM7DE-MB-02-1T-00

Parts verification Error

PCB Bar Code Recog

Error

Solutions to errors

Error Code

Error Message

Cause Inspection and Solution

Any of the following causes

is likely:

1) Recognition mark is out of

camera's view.

2) Recognition error

occurred due to dirt on PCB.

3) PCB barcode recognition

coordinates are incorrect.

(Single stop error occurred.)

Take measures shown with the

same number as that of the cause.

1) Using the inching function, move

the camera to the recognition mark

position and press the [Re-

recognize] button.

2) After cleaning the recognition

camera and PCB, press the [Re-

recognize] button. If the

recognition error occurs again,

move the camera to the

recognition mark position with the

[Pass] button or inching function

and press the [Manual set] button.

[Pass]: Pass the PCBs.[Manual

set]: Saves the inching amount as

the offset.

3) Choose [Production data] -

[Correct] - [PCB] - [PCB recog.]

and enter the correct PCB barcode

recognition coordinates.

40412

Component verification failed.

(Single stop error occurred.)

Verify the components again.If

something is wrong, replace with the

correct component.

40413

2-1-3-35