N7201A618E00_0309.pdf - 第109页

NPM–W 2 EJM7DE-MB-02 -1T-00 Loacl Height Result Range Err Mount point recog error Solutions to errors Error Code Error Message Cause Inspection and Solution Any of the following causes is likely: 1) R ecognition mark is …

NPM–W2 EJM7DE-MB-02-1T-00

Stamper return origin

Error

Stamper unit initial error

The trans unit is not set up.

Error

Message

Troubleshooting

2-1-3

Single stop error 20

Error Code

Error Message

Cause Inspection and Solution

Transcript unit cannot be

confirmed.

(Single stop error occurred.)

Take any of the following measures:

1) Make sure the transcript unit is

set properly.

2) Remove and insert the transcript

unit.

40421

Failed to Initialize the

transcript unit properly.

(Single stop error occurred.)

Take any of the following measures:

1) Check the transcript unit.

2) Remove the transcript unit and

insert it again.

40422

Failed to return the transcript

unit to origin properly.

(Single stop error occurred.)

Take any of the following measures:

1) Check the transcript unit.

2) Remove the transcript unit and

insert it again.

40423

2-1-3-38

NPM–W2 EJM7DE-MB-02-1T-00

Loacl Height Result

Range Err

Mount point recog error

Solutions to errors

Error Code

Error Message

Cause Inspection and Solution

Any of the following causes

is likely:

1) Recognition mark is out of

camera's view.

2) Recognition error

occurred due to dirt on

PCB^ etc.

3) Incorrect mounting point

recognition coordinates

(Single stop error occurred.)

Take measures shown with the

same number as that of the cause.

1) Using the inching function, move

the camera to the recognition mark

position and press the [Re-

recognize] button.

2) After cleaning the recognition

camera and PCB, press the [Re-

recognize] button. If the

recognition error occurs again,

press the [No Recognition] or

[Pass] button. [No Recognition]:

Move to the next action without

recognition. [Pass]: Pass the PCB.

3) Choose [Production data] -

[Correct] - [Mount] and enter the

correct mounting point recognition

coordinates.

40424

There are variations in height

measurement results.

(Single stop error occurred.)

Take any of the following measures:

1) Check the PCB.

2) Check the setting value of the

spot height result tolerance.

40425

2-1-3-39

NPM–W2 EJM7DE-MB-02-1T-00

Nozzle barcode recog

error

Syringe trans empty

Trans auto-supply error

Trans material empty

Height Measurement Error

Error

Message

Troubleshooting

2-1-3

Single stop error 21

Error Code

Error Message

Cause Inspection and Solution

Error occurred during

measurement of height

sensor.

(Single stop error occurred.)

Check the situation of the error

occurred and error message, and

contact PFSC.

40426

Material in the transcript table

is insufficient.

(Single stop error occurred.)

Supply the material to the stamper

table.

40427

Any of the following causes

is likely:

1) Tip of the syringe is

clogged.

2) Transcript material for the

syringe is insufficient.

3) Syringe not installed

properly.

(Single stop error occurred.)

Take measures shown with the

same number as that of the cause.

1) Check the tip of the syringe.

2) Supply transcript material to the

syringe.

3) Make sure the syringe is installed.

40428

Transcript material in the

syringe is insufficient.

(Single stop error occurred.)

Supply transcript material to the

syringe.

40429

Nozzle in the changer to be

used for production does not

agree with the one saved in

the production data.

(Single stop error occurred.)

Check the barcode of the target

nozzle in the changer.

40430

2-1-3-40