N7201A618E00_0309.pdf - 第89页

NPM–W 2 EJM7DE-MB-02 -1T-00 Inspect Mc Fe edback Err Pick-up Pos Gap Detec t Parts verify Request Stop Filter Clearing Solutions to errors Error Code Error Message Cause Inspection and Solution Any of the following cause…

NPM–W2 EJM7DE-MB-02-1T-00

Auto Product Change Err

Abnormal Pickup Height

Pickup Height Measure

Err

Error

Message

Troubleshooting

2-1-3

Single stop error 10

Error Code

Error Message

Cause Inspection and Solution

The head lowered to the soft

limit before detected by the

cushion end sensor^

because either the feeder or

tray was improperly set.

(Single stop error occurred.)

Make sure the feeder or pallet is set

properly. Make sure the nozzle is

attached to the head properly.

40355

Any of the following causes

is likely:

1) There is obstacle at the

pickup part.

2) Feeder not set.

3) Nozzle not attached.

(Single stop error occurred.)

Take measures shown with the

same number as that of the cause.

1) Remove the obstacle from the

pickup part.

2) Set the feeder.

3) Attach the nozzle.

40356

Any of the following causes

is likely:

1) Failed to switch the

production data.

2) Failed to notify the

production changeover

information to the next

process machine.

(Single stop error occurred.)

Take measures shown with the

same number as that of the cause.

1) Make sure the production data

can be loaded from the LNB.

2) Check the communication and

setting conditions of the next

process machine.

40357

2-1-3-18

NPM–W2 EJM7DE-MB-02-1T-00

Inspect Mc Feedback Err

Pick-up Pos Gap Detect

Parts verify Request Stop

Filter Clearing

Solutions to errors

Error Code

Error Message

Cause Inspection and Solution

Any of the following causes

is likely:

1) Nozzle filter clogged.

2) Nozzle clogged.

(Single stop error occurred.)

Take measures shown with the

same number as that of the cause.

1) Clean the nozzle filter.

2)Clean the nozzle.

40358

Stop information arrived from

the component verification

system.

(Single stop error occurred.)

Production can be restarted if the

request to stop command is reset.

40359

Feeder's pickup position is

displaced by the unit of pitch.

(Single stop error occurred.)

Adjust the pickup position with the

[Feed] button.

40360

Same kind of error occurred

10 times in one hour at each

mounting point.

(Single stop error occurred.)

Press the [Solution] button.

40361

2-1-3-19

NPM–W2 EJM7DE-MB-02-1T-00

Host Feeder Time Out

Feeder Setting Error

Mount Pos Teach Ope.

Err

Servo Off Error

Error

Message

Troubleshooting

2-1-3

Single stop error 11

Error Code

Error Message

Cause Inspection and Solution

Any of the following causes

is likely:

1) Axis movement is

disabled because the servo

switch is OFF.

2) Axis movement is

disabled because interlock

is engaged in the adjoining

machine.

(Single stop error occurred.)

Take measures shown with the

same number as that of the cause.

1) Choose [Machine] - [Adjust] - [All]

- [Input confirm] and check the

condition of the servo switch and

contact PFSC.

2) Release the interlock of the

adjoining machine.

40362

Teaching started with the

setting that does not match

the operating condition for

teaching. Or teaching

condition cannot be met due

to error during teaching.

(Single stop error occurred.)

Reset the tray counter. Eliminate

the cause if recognition or pickup

error has occurred. Reset the bad

head setting.

40363

Failed to make feeder setting.

(Single stop error occurred.)

Make sure the attached feeder is

correct. If something is wrong with

the feeder, replace it with a proper

one.

40364

Timeout occurred during

waiting for completion of

preparation for pickup by

host feeder.

(Single stop error occurred.)

Check the feeder.

40365

2-1-3-20